Thanks.
That was one of the mysteries of the universe I've been looking for all
these years.
When someone told me they wanted to use Tray 3 in this device, then I
later learned to use "data_intray=3", I only had a sneaking suspicion in
my mind this was somehow, wrong.
Tracy Johnson
Office 1-757-766-4318
[log in to unmask]
> -----Original Message-----
> From: HP-3000 Systems Discussion
> [mailto:[log in to unmask]] On Behalf Of Dave Powell, MMfab
> Sent: Tuesday, April 20, 2010 3:15 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Paper Trays on a HP 4250tn
>
> Many, MANY moons ago, someone from HP posted a list of tray
> number codes. I
> have used them only in environment files with escape codes
> like <esc>&l#H,
> but I *GUESS* you would use the same numbers for data_intray
> setup (?).
> That's an "ell" after the ampersand.
>
> I can only vouch for a few of them, and only on a few models,
> like 5N, 4050,
> 4100 & P3005. esc&l4H pulls from tray 1, and esc&l0H pulls
> from any tray
> that I haven't set up in the printer's own configuration as
> having special
> paper.
>
> Anyway, the list says "3" means manual feed and you need "5"
> to pull from
> tray 3. Intuitive much ? Good luck doing anything with
> trays without the
> magic list :)
>
> Here it is, except that I have replaced the description of '0' in the
> original posting with a description I pulled from some old printer
> manual-on-cd.
>
> 0 = "any unlocked tray (was "prints or ejects current page")
> 1 = Tray 2
> 2 = manual feed, paper
> 3 = manual feed, envelope
> 4 = Tray 1
> 5 = Tray 3
> 6 = Envelope Feeder
> 7 = auto select
> 8 = Tray 4
> 20-69 = external trays
>
>
>
> ----- Original Message -----
> From: "Tracy Johnson" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, April 20, 2010 09:10
> Subject: Re: [HP3000-L] Paper Trays on a HP 4250tn
>
>
> After a couple of years after making the recommended changes
> in this post,
> the users came back again telling the HP3000 paper is still
> using the Manual
> Tray. The printer is still a 4250tn configured as follows.
>
> 970 (network_address = 172.16.52.66 PJL_SUPPORTED=FALSE
> JAM_RECOVERY=TRUE
> MANUALFEED=OFF data_intray=3)
>
> The only thing I can think of is there a one to one
> correlation between what
> the 4250 thinks tray 3 is versus what the HP thinks tray 3
> is? i.e., does
> telling it data_intray=3 equate to the Manual Tray on the 4250tn?
>
> Or should I take manualfeed=off?
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|