Subject: | |
From: | |
Reply To: | |
Date: | Fri, 13 Oct 2000 14:39:15 -0700 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Have you done a START NORECOVERY to activate the change?
> -----Original Message-----
> From: Sam Knight [mailto:[log in to unmask]]
> Sent: Friday, October 13, 2000 2:22 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Help with Autoreply
>
>
> Below is the message I get when running VSTORE in a job, with a file
> equate of FILE=T;DEV=8
>
> THE FOLLOWING REPLIES ARE PENDING:
> 17:20/#J6249/262/IS "T" ON LDEV#8 (Y/N)?
>
>
> Denys Beauchemin wrote:
> >
> > What kind of reply is asked?
> >
> > I have included the sysgen configuration for the DLT drive
> in the DLT Robotic
> > library.
> > io> ld 13
> > LDEV: 13 DEVNAME: OUTDEV: 0
> MODE: R
> > ID: DLT7000 RSIZE: 128
> DEVTYPE: TAPE
> > PATH: 44.1.0 MPETYPE: 24
> MPESUBTYPE: 8
> > CLASS: TAPE
> >
> > As you can see, it's similar to yours.
> >
> > The drive is in a robotic library and the robot feeds in
> the appropriate tape
> > when requested to do so by the backup software. The only
> time that I have seen
> > a reply pending on this drive is when the tape takes an
> inordinately long time
> > to load. The backup software has built-in configurable
> delays so that it waits
> > a certain amount of time before it starts to access the
> tape after it has been
> > loaded by the robot.
> >
> > If you try to access the tape before you get the AVR
> message at the console,
> > you will get the reply as the tape is probably not ready.
> Remember, a DLT
> > drive can take several minutes to get the tape on-line.
> >
> > Kind regards,
> >
> > Denys. . .
> >
> > Denys Beauchemin
> > HICOMP
> > (800) 323-8863 (281) 288-7438 Fax: (281) 355-6879
> > denys at hicomp.com www.hicomp.com
> >
> > -----Original Message-----
> > From: Sam Knight [SMTP:[log in to unmask]]
> > Sent: Friday, October 13, 2000 3:53 PM
> > To: [log in to unmask]
> > Subject: Help with Autoreply
> >
> > I have device 8 which is a DLT7000 on a HP3000-979
> configured in sysgen
> > as follows:
> >
> > io> LD 8
> > LDEV: 8 DEVNAME: OUTDEV: 0
> MODE: R
> > ID: DLT7000 RSIZE: 128
> DEVTYPE: TAPE
> > PATH: 10/4/24.1.0 MPETYPE: 24
> MPESUBTYPE: 8
> > CLASS: TAPE
> >
> > io> LC TAPE
> >
> > CLASSNAME MODE MIN MODE DCC MODE # DCC LDEV
> > --------- ------- -------- -------- ----- ----
> > TAPE default ncio 0 7, 8,
> >
> > I did a modify device with mode=autoreply, and when I read a tape it
> > still asks for a reply. I am not sure what the mode on the
> class tape
> > should be. Both of the sysgen displays are as the system
> was originally
> > set up.
> >
> > --
> > Regards,
> >
> > Sam Knight, Senior Programmer/Analyst
> > Jacksonville University
> > Jacksonville, Florida 32211
>
> --
> Regards,
>
> Sam Knight, Senior Programmer/Analyst
> Jacksonville University
> Jacksonville, Florida 32211
>
|
|
|