For example (note it is pjl_supported NOT pjl_enabled - I should never rely
on memory, sorry):
617 (network_address = 172.17.200.92
snmp_enabled=false
pjl_supported=false
jam_recovery=false
setup_file=pcelite.hpenv.sys) #my comments
> -----Original Message-----
> From: STEPHEN HUNTER [mailto:[log in to unmask]]
> Sent: Thursday, October 05, 2000 10:57 AM
> To: [log in to unmask]
> Subject: RE: [HP3000-L] Cannon Laser Printer
>
>
> Thanks for the input, but where in the NPCONFIG file would the snmp
> statement go??
>
> 617 (network_address = 172.17.200.92)
>
> is it within the () or after with a ; or what???
>
> Thanks..
>
> >From: John Burke <[log in to unmask]>
> >To: 'STEPHEN HUNTER' <[log in to unmask]>,
> [log in to unmask]
> >Subject: RE: [HP3000-L] Cannon Laser Printer
> >Date: Thu, 5 Oct 2000 10:52:43 -0700
> >
> >You are not using an HP JetDirect card/box. Put the
> following directive in
> >npconfig for this printer: snmp_enabled=false
> >
> >Now stop and re-start the spooler for this device class. If
> the Cannon
> >understand PCL and you have the appropriate setup file, you
> should be in
> >business. If on the other hand the Cannon does not speak
> PCL, no amount of
> >fiddling with make it work.
> >
> >Note: you may also need to set: pjl_enabled=false
> >
> >HTH,
> >John Burke
> >
> > > -----Original Message-----
> > > From: STEPHEN HUNTER [mailto:[log in to unmask]]
> > > Sent: Thursday, October 05, 2000 10:06 AM
> > > To: [log in to unmask]
> > > Subject: [HP3000-L] Cannon Laser Printer
> > >
> > >
> > > Hello Everybody,
> > >
> > > Thanks to all who helped me with my last problem.. I have
> > > another question
> > > however. Has anyone ever configured a Cannon Printer on the
> > > HP3000? I have
> > > 2 rather large Cannon Printers that I would like to use as
> > > "backup printers"
> > > in case of any hardware problems with my Regular 5si/D640.
> > > When I set up
> > > these printers, the following error occurs:
> > >
> > > Output spooler, LDEV #616: SNMP error SNMP_NoSuchName reported
> > > while retrieving printer status.
> > > Native Mode Spooler message 9656
> > >
> > > 13:00/304/Output spooler, LDEV #616: Cannot communicate
> with network
> > > printer.
> > > Check network xport config, NPCONFIG.PUB.SYS, xport and
> links started
> > > status,
> > > intermediate network, and printer status.
> > > Native Mode Spooler message 9662
> > >
> > > Now, this printer is defined in NPCONFIG.PUB.SYS and is
> set up through
> > > IOCONFIG. I just set a regular Laser Printer(HP of course)
> > > in Puerto Rico
> > > yesteday, and everything works fine. Does anybody have any
> > > info on this..
> > >
> > > Again, I thank everybody for their input..
> > >
> > >
> > > ______________________________________________________________
> > > ___________
> > > Get Your Private, Free E-mail from MSN Hotmail at
> >http://www.hotmail.com.
> >
> >Share information about yourself, create your own public profile at
> >http://profiles.msn.com.
>
> ______________________________________________________________
> ___________
> Get Your Private, Free E-mail from MSN Hotmail at
http://www.hotmail.com.
Share information about yourself, create your own public profile at
http://profiles.msn.com.
|
