Well I use it on DLT's all the time when I need to put a tape back online
and it works fine
james
-----Original Message-----
From: Rick Clark [mailto:[log in to unmask]]
Sent: Friday, August 04, 2000 2:14 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Help - Setting AutoReply & AutoEject
We stream a job out of the SYSSTART file that performs such functions.. I
was always under the impression that DEVCTRL did not work on DLT's. Not sure
how or why but did not pursue any further. I am going to run with it and see
what happens.
-----Original Message-----
From: Joseph Rosenblatt [mailto:[log in to unmask]]
Sent: Friday, August 04, 2000 3:52 PM
To: [log in to unmask]; [log in to unmask]
Subject: RE: [HP3000-L] Help - Setting AutoReply & AutoEject
You must reissue the DEVCTRL command after every restart of the system. I
have also not been able to get it to work when I put it in SYSSTART. It just
hangs there.
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]]On
Behalf Of Newton, Tony
Sent: Friday, August 04, 2000 3:16 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Help - Setting AutoReply & AutoEject
Cool......I didn't know you could do that. Does that functionality go away
after you bounce the system?
> -----Original Message-----
> From: Newton, Ernie [SMTP:[log in to unmask]]
> Sent: Friday, August 04, 2000 12:01 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Help - Setting AutoReply & AutoEject
>
> Oops, nobody asked about putting a tape online, did they...(it's Friday)
>
> What I meant to answer was the auto reply...
>
> If you have the program on your system you can do this.
>
> RUN AUTOREP.UTIL.SYS;PARM=7
>
> If you want to turn it back off, use -7.
>
> -----Original Message-----
> From: Newton, Ernie
> Sent: Friday, August 04, 2000 11:55 AM
> To: [log in to unmask]
> Subject: RE: [HP3000-L] Help - Setting AutoReply & AutoEject
>
>
> Actually, you can put the tape online by using devctrl also...
>
> DEVCTRL.MPEXL.TELESUP 7;LOAD=ONLINE
>
> That'll do it...
>
> -----Original Message-----
> From: Newton, Tony [mailto:[log in to unmask]]
> Sent: Friday, August 04, 2000 11:48 AM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Help - Setting AutoReply & AutoEject
>
>
> Cathy,
>
> Part 1:
> You set up devices for autoreply inside of sysgen. You can do something
> similar to the following.
> :Sysgen
> sysgen> IO
> io>md 7;mode=autoreply
> io>hold
> io>exit
> sysgen>keep
> sysgen>exit
>
> Part 2:
> You can specify a device to autoeject by using DEVCTRL.MPEXL.TELESUP.
> echo ******************* DEVCTRL SYNTAX ERROR ***********************
> echo
> echo Usage Syntax:
> echo DEVCTRL LDev COMPRESSION=Compress EJECT=Eject LOAD=Load where
> echo LDev - Logical Device Number (Required)
> echo Compress - [Enable | Disable | Nochange]
> echo Eject - [Enable | Disable | Nochange]
> echo Load - [Online | Offline | Nochange]
> echo
> echo ******************* DEVCTRL SYNTAX ERROR ***********************
>
> Hope that this helps.
> ____
> Tony Newton | [log in to unmask]
> HP Systems Admin | (503) 574-5831
> Providence Health Plan | www.providence.org
>
>
>
> > -----Original Message-----
> > From: Cathy Gunderson [SMTP:[log in to unmask]]
> > Sent: Friday, August 04, 2000 11:38 AM
> > To: [log in to unmask]
> > Subject: [HP3000-L] Help - Setting AutoReply & AutoEject
> >
> > I need help on how to set the Auto Reply and Auto Eject for LDEV 7 on.
> I
> > believe this is done with a SET command but can't remember the format of
> > the
> > command. We are on MPE/iX 6.0.
> > Thanks.
> >
> > Cathy
|