I guess that means the one in the A500 that we have at Longs doesn't work.
Hmm .. Guess, I should tell that A-class box, since it has worked since we installed in about 2003 ... Probably because it just doesn't know any better.
From our System config:
A500-200-140 IXH - MPE Test & Development System
And
PATH: 0/0/2 LDEV:
ID: PCI_DEVICE TYPE: BC
PMGR: PCI_DEVICE_MGR PMGRPRI: 2
LMGR: MAXIOS: 0
PATH: 0/0/2/0 LDEV:
ID: A5150A TYPE: DA
PMGR: PCI_SCSI_DAM PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.5 LDEV:
ID: PSEUDO TYPE: DA
PMGR: TRANSPARENT_MGR PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.5.0 LDEV: 9
ID: HP7980S TYPE: TAPE
PMGR: SCSI_TAPE2_DM PMGRPRI: 10
LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
--
Jim Alexander Longs Drug Stores
Sr. Systems Programmer 925-210-6901
The opinions expressed are Mine and not Longs Drugs
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of Craig Lalley
Sent: Thursday, April 30, 2009 2:00 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Mpe: HP7980S Configuration on A400 - mapper2 output
Karsten,
It appears you are trying to use a dual-headed card in an A-class.
I believe the A5150A is a dual port SCSI controller. It is not supported in an A-class MPE configuration. There is no driver for it.
Sorry,
-Craig
--- On Thu, 4/30/09, Karsten Brøndum <[log in to unmask]> wrote:
> From: Karsten Brøndum <[log in to unmask]>
> Subject: Re: Mpe: HP7980S Configuration on A400 - mapper2 output
> To: [log in to unmask]
> Cc: [log in to unmask]
> Date: Thursday, April 30, 2009, 3:32 PM
> Booting...
> Boot IO Dependent Code (IODC) revision 1
>
> HARD Booted.
> MMSAVE Version 2.5
> DUMPAREA found, save main memory to disc
> ISL loaded
>
> ISL Revision A.00.43 Apr 12, 2000
>
> ***************************************************************************
> ******
> ******
> ****** Offline Diagnostic Environment
> ******
> ******
> ******
> ****** (C) Copyright Hewlett-Packard Co 1993-2000
> ******
> ****** All Rights Reserved
> ******
> ******
> ******
> ****** HP shall not be liable for any damages resulting
> from the ******
> ****** use of this program.
> ******
> ******
> ******
> ****** TC Version A.02.22
> ******
> ****** SysLib Version A.00.75
> ******
> ****** Loader Version A.00.61
> ******
> ****** Mapfile Version A.01.27
> ******
> ******
> ******
> ***************************************************************************
>
> Type HELP for command information.
>
> ***************************************************************************
> ******
> ******
> ****** MAPPER2
> ******
> ******
> ******
> ****** Copyright (C) 1998-2000 by Hewlett-Packard
> Company ******
> ****** All Rights Reserved
> ******
> ******
> ******
> ****** HP shall not be liable for any damages resulting
> from the ******
> ****** use of this program.
> ******
> ******
> ******
> ****** Version B.00.17
> ******
> ******
> ******
> ***************************************************************************
>
> Type HELP for command information.
>
>
> STARTING EXECUTION OF MAPPER2
>
> Processor Identification:
> Hardware Model: 5D6H, Revision: 0
> Software Model: 4H, Revision: 0
> Hardware ID: 0, Software ID: 1342988618 (unsigned
> decimal)
> HP-UX Model String: 9000/800/A400-44
> MPE/XL Model String: e3000/A400-100-11#N
> Processor Board Revisions:
> CPU - CPU Chip: 768
> PDC - Processor Dependent Code: 41.10
> Cache and TLB Sizes:
> Instruction Cache: 512 K bytes, Instruction TLB:
> 160 entries
> Data Cache: 1024 K bytes, Data TLB:
> 160 entries
> Co-processors:
> Floating Point Co-processor(s) installed
>
> I/O Configuration:
> Type HW
> SW Revisions
> Path Component Name ID Model
> Model Hdwr Firm
> (77/124) Continue?
> ---------- ----------------------------------- ----- -----
> ----- ----- -----
> 0 Astro BC Runway Port CH 582H
> BH 0 0
> 0/0 Elroy PCI Bridge DH 782H
> AH 0 0
> 0/0/0/0 Ethernet Controller 1011H 0019H
> 103CH 104FH 41H
> 0/0/1/0 SCSI Bus Controller 1000H 000BH
> 0000H 0000H 07H
> 0/0/1/1 SCSI Bus Controller 1000H 000BH
> 0000H 0000H 07H
> 0/0/1/1.15.0
> SEAGATE ST39204LC disk drive - - -
> - HP04
> 0/0/2/0 Symbios SCSI Controller 1000H 000FH
> 0000H 0000H 14H
> 0/0/2/0.5.0
> 7980S SCSI mag tape unit - - -
> - A731
> 0/0/2/1 Symbios SCSI Controller 1000H 000FH
> 0000H 0000H 14H
> 0/0/2/1.15.0
> SEAGATE ST318404LC disk drive - - -
> - HP04
> 0/0/4/0 Serial Controller 103CH 1048H
> 103CH 1049H 02H
> 0/0/5/0 Serial Controller 103CH 1048H
> 103CH 104AH 02H
> 0/2 Elroy PCI Bridge DH 782H
> AH 0 0
> 0/2/0/0 Ethernet Controller 1011H 0019H
> 103CH 1066H 41H
> 0/4 Elroy PCI Bridge DH 782H
> AH 0 0
> (96/124) Continue?
> 0/6 Elroy PCI Bridge DH 782H
> AH 0 0
> 8 Memory Controller (256 Mbytes) 1H 9BH
> 9H 0 0
> Slot 01 128M Active
> Slot 02 128M Active
> Slot 03 - -
> Slot 04 - -
> Slot 05 - -
> Slot 06 - -
> Slot 07 - -
> Slot 08 - -
> 160 Processor 0H 5D6H
> 4H 0 0
>
>
>
> Craig Lalley wrote:
> > Karsten,
> >
> > That's a good start. Every one has commented that
> the drive was seen in Mapper. Can you post the output from
> MAPPER2?
> >
> > -Craig
> >
> >
> >
> > --- On Thu, 4/30/09, Karsten Brøndum
> <[log in to unmask]> wrote:
> >
> >
> >> From: Karsten Brøndum <[log in to unmask]>
> >> Subject: Re: Mpe: HP7980S Configuration on A400
> >> To: [log in to unmask]
> >> Date: Thursday, April 30, 2009, 2:50 PM
> >> io>
> >> io> LP 0/0
> >> PATH: 0/0
> LDEV:
> >> ID: PAT_PCI_BC TYPE:
> BC
> >> PMGR: PCI_ELROY_MGR
> PMGRPRI: 2
> >> LMGR:
> MAXIOS: 0
> >>
> >> io> lp 0/0/2
> >> PATH: 0/0/2
> LDEV:
> >> ID: PCI_DEVICE TYPE:
> BC
> >> PMGR: PCI_DEVICE_MGR
> PMGRPRI: 2
> >> LMGR:
> MAXIOS: 0
> >>
> >> io> lp 0/0/2/0
> >> PATH: 0/0/2/0
> LDEV:
> >> ID: A5150A TYPE:
> DA
> >> PMGR: PCI_SCSI_DAM
> PMGRPRI: 6
> >> LMGR:
> MAXIOS: 0
> >>
> >> io>
> >>
> >> Thanks,
> >> Karsten.
> >>
> >> Gilles Schipper wrote:
> >>
> >>> Can you show us, in sysgen, io
> >>>
> >>> lp 0/0
> >>> lp 0/0/2
> >>> lp 0/0/2/0
> >>>
> >>> At 08:51 AM 2009-04-30, SUBSCRIBE HP3000-L
> Karsten
> >>>
> >> Brondum wrote:
> >>
> >>>> Trying to configure an HP7980S on A400,
> but
> >>>>
> >> receive
> >>
> >>>> LLIO Device configuration Error -11
> >>>>
> >>>> ODE / mapper 2 reports HP7980S on
> /0/0/2/0.5.0
> >>>>
> >> which matches path printed
> >>
> >>>> on back of A400. Did the following
> configuration:
> >>>>
> >>>> AP PATH=0/0/2/0.5;ID=PSEUDO
> >>>> AD 9;PATH=0/0/2/0.5.0;ID=HP7980S
> >>>>
> >>>> io> LD 9
> >>>> LDEV: 9 DEVNAME:
> OUTDEV:
> >> 0 MODE:
> >>
> >>>> ID: HP7980S
> RSIZE:
> >> 128 DEVTYPE: TAPE
> >>
> >>>> PATH: 0/0/2/0.5.0
> MPETYPE:
> >>>>
> >> 24 MPESUBTYPE: 5
> >>
> >>>> CLASS: TAPE
> >>>>
> >>>> :SHOWME
> >>>> USER: #S2,MANAGER.SYS,PUB (NOT IN
> BREAK)
> >>>> RELEASE: C.70.00 MPE/iX HP31900 C.39.06
> USER
> >>>>
> >> VERSION: C.70.00
> >>
> >>>> CURRENT: THU, APR 30, 2009, 2:48 PM
> >>>> LOGON: THU, APR 30, 2009, 2:39 PM
> >>>>
> >>>>
> >>>> Any help greatly appreciated
> >>>> Karsten.
> >>>>
> >>>> * To join/leave the list, search archives,
> change
> >>>>
> >> list settings, *
> >>
> >>>> * etc., please visit
> >>>>
> >> http://raven.utc.edu/archives/hp3000-l.html *
> >>
> >>>> No virus found in this incoming message.
> >>>> Checked by AVG - www.avg.com
> >>>> Version: 8.5.285 / Virus Database:
> 270.12.10/2088
> >>>>
> >> - Release Date: 04/30/09 06:01:00
> >>
> >>>
> >>
> -------------------------------------------------------------------------------------------------
> >>
> >>
> >>> Gilles Schipper
> >>> GSA Inc.
> >>> HP System Administration Specialists
> >>> 300 John Street, Box 87651 Thornhill, ON
> Canada L3T
> >>>
> >> 7R4
> >>
> >>> Voice: 905.889.3000 Fax: 905.889.3001
> >>> email: [log in to unmask] web:
> http://www.gsainc.com
> >>>
> >>>
> >>
> -------------------------------------------------------------------------------------------------
> >>
> >>
> >>>
> >>>
> >>>
> >> * To join/leave the list, search archives, change
> list
> >> settings, *
> >> * etc., please visit
> >> http://raven.utc.edu/archives/hp3000-l.html *
> >>
> >
> >
> >
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
