Although ldev 10 is really only a pseudo-type device, you need to get
around the LLIO error so that ldev 10 is recognized.
The problem appears to be related to the path you have configured.
The fact that the system is complaining about path 4.1.7 suggests that you
have it pathed to a single-ended SCISI controller.
In SYGEN I/O, if you issue the following LP commands, you will discover
similar to the following:
LP 4.1 - will probably indicate device id PSEUDO
LP 4 - will probably indicate device id HPA1741A, which represents a
SINGLE-ENDED SCSI controller, which supports only 7 devices (id's 0 thru 6).
You have 2 choices.
1. Choose a pseudo device other than one ending in 7 on that specific
controller - assuming you have an available spare. (You will also need to
add the appropriate id=pseudo path.)
2. Choose a completely different PSEUDO path for this PSEUDO device, even
if it does not really exist. For example, configure the following paths:
AP 8 id=A1703-60003-SCSI
AP 8.1 id=pseudo
AD 10 path=8.1.0 .......... (This is your pseudo-streams device)
The above assumes that there is no real device at path 8 (and below).
Option 1 might be easier, although option 2 is more flexible if you used up
all available SCSI addresses on your existing controller.
Of course, you then need to SHUTDOWN, START NORECOVERY, and all that.
Hope that helps.
At 11:45 AM 98/05/13 -0500, you wrote:
>Thank you all for your prompt replies. However, it still doesn't work.
>Here are the error messages which appear during boot:
>
>...
>The path 4.1.7 was configured but is not available
>LLIO error - subsys: 129, proc num: 58, error_num: -15
>for path 4.1.8
>ERROR - LLIO device configuration error: -11
> status - subsys: #150 info: #-11
>...
>STREAMS 10
>STREAMS device cannot be a terminal (CIERR 3067)
>...
>STREAM NETJOB.PUB.SYS
>Stream facility not enables. See operator. (CIERR 82)
>...
>
>The last message does me no good, I AM the operator.
>I have not been able to find any info on any of this on the HP LaserROM for
>MPE 5.0. We are running MPE 5.0, and (for financial reasons, surprise,
>suprise) we have no HP support either for hardware or software. (Not MY
>decision)
>Thanks again, y'all are great.
>W.
>[log in to unmask]
>
>Gary Nolan wrote:
>
>> Hi,
>> I just checked my system config for ldev 10 and here it is:
>> LDEV: 10 DEVNAME: OUTDEV: LP MODE: JA
>> ID: HPC1503B RSIZE: 128 DEVTYPE: TAPE
>> PATH: 52.9.0 MPETYPE: 24 MPESUBTYPE: 7
>> CLASS: JOBTAPE
>>
>> We are on a 947. Hope this helps.
>> Gary Nolan
>> Sydney Steel Corporation
>>
>> -----Original Message-----
>> From: Warren Cartwright [SMTP:[log in to unmask]]
>> Sent: May 12, 1998 7:36 PM
>> To: [log in to unmask]
>> Subject: HELP ldev 10 spooler
>>
>> I inadvertantly deleted ldev 10 on our 3000-920. I can't figure out how
>> to get it back successfully!
>>
>> I have added an LP device on ldev 6 and the ldev 10, sysgen> io>ld looks
>> like this:
>>
>> io> ld 6
>> LDEV: 6 DEVNAME: OUTDEV: 0
>> MODE: OS
>> ID: HP2566A RSIZE: 66 DEVTYPE: LP
>>
>> PATH: 4.1.7 MPETYPE: 32
>> MPESUBTYPE: 9
>> CLASS: LP
>>
>> io> ld 10
>> LDEV: 10 DEVNAME: OUTDEV: LP MODE: JA
>> ID: HPC1501A RSIZE: 128 DEVTYPE:
>> TAPE
>> PATH: 4.1.8 MPETYPE: 24
>> MPESUBTYPE: 6
>> CLASS: JOBTAPE
>>
>> io>
>>
>> When I boot the machine, I get errors wrt ldev 6 and 10. When I type
>> streams 10, the computer tells me that the spool device can't be a
>> terminal and aborts.
>>
>> How do I get my streams back?!?
>>
>> W.
>> [log in to unmask]
>
>
---------------------------------------------------------------------------
Gilles Schipper
GSA Inc.
HP3000 & HP9000 System Administration Specialists
300 John Street, Box 87651 Thornhill, ON Canada L3T 7R4
Voice: 905.889.3000 Fax: 905.889.3001
Internet: [log in to unmask]
---------------------------------------------------------------------------
|
