Everyone,
Bill M. reported to me offline that path 0/0/2/0 is NOT an add in card.
I do think he is correct. Heck, I configured two A-classes this weekend, you would think I would remember THAT.
The add on paths I remember are 0/2/0/0, 0/4/0/0, 0/6/0/0 and 0/6/2/0, I do know the paths are clearly marked on the back of the A-class. (I looked there several times myself.)
So 0/0/2/0 is one of the internal paths. Can someone please look at the back of an A-class for us?
I did look at a default configuration CONFALC3.SYS
surprise, surprise... (see below)
One side has the fake 'streams' device LDEV 10, the phoney LP 6, and a real DDS3 tape drive.
The other side has a real scsi disc drive.
This is one of the default configurations from HP. yet the A5150A is not 'supported'.
-Craig
PATH: 0/0/2 LDEV:
ID: PCI_DEVICE TYPE: BC
PMGR: PCI_DEVICE_MGR PMGRPRI: 2
LMGR: MAXIOS: 0
PATH: 0/0/2/0 LDEV:
ID: A5150A TYPE: DA
PMGR: PCI_SCSI_DAM PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.16 LDEV:
ID: PSEUDO TYPE: DA
PMGR: TRANSPARENT_MGR PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.16.0 LDEV: 6
ID: LP_PP_ID TYPE: PP
PMGR: SCSI_DISC_DM PMGRPRI: 10
LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
PATH: 0/0/2/0.17 LDEV:
ID: PSEUDO TYPE: DA
PMGR: TRANSPARENT_MGR PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.17.0 LDEV: 10
ID: JOBTAPE_ID TYPE: TAPE
PMGR: SCSI_DISC_DM PMGRPRI: 10
LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
PATH: 0/0/2/0.6 LDEV:
ID: PSEUDO TYPE: DA
PMGR: TRANSPARENT_MGR PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/0.6.0 LDEV: 7
ID: HPC1553A TYPE: TAPE
PMGR: SCSI_TAPE_DM PMGRPRI: 10
LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
PATH: 0/0/2/1 LDEV:
ID: A5150A TYPE: DA
PMGR: PCI_SCSI_DAM PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/1.15 LDEV:
ID: PSEUDO TYPE: DA
PMGR: TRANSPARENT_MGR PMGRPRI: 6
LMGR: MAXIOS: 0
PATH: 0/0/2/1.15.0 LDEV: 2
ID: ST39103LC TYPE: DISC
PMGR: SCSI_DISK_AND_ARRAY_DM PMGRPRI: 8
LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
--- On Thu, 4/30/09, Jim Alexander <[log in to unmask]> wrote:
> From: Jim Alexander <[log in to unmask]>
> Subject: Re: Mpe: HP7980S Configuration on A400 - mapper2 output
> To: [log in to unmask]
> Date: Thursday, April 30, 2009, 4:35 PM
> The important thing is that we don't have anything else
> on that card .. So it is terminated on the other port.
>
> That is probably the differnce here.
>
>
> --
> Jim Alexander Longs Drug Stores
> Sr. Systems Programmer 925-210-6901
> The opinions expressed are Mine and not Longs Drugs
>
>
>
> -----Original Message-----
> From: John Lee [mailto:[log in to unmask]]
> Sent: Thursday, April 30, 2009 2:36 PM
> To: Jim Alexander; [log in to unmask]
> Subject: Re: [HP3000-L] Mpe: HP7980S Configuration on A400
> - mapper2 output
>
> Very interesting. Do you have anything connected to it?
>
> John Lee
>
>
>
> At 02:08 PM 4/30/09 -0700, Jim Alexander wrote:
> > I guess that means the one in the A500 that we have
> at Longs doesn't
> > work.
> >
> >Hmm .. Guess, I should tell that A-class box, since it
> has worked since we
> >installed in about 2003 ... Probably because it just
> doesn't know any better.
> >
> > From our System config:
> >
> >A500-200-140 IXH - MPE Test & Development System
> >
> >And
> >
> >PATH: 0/0/2 LDEV:
> > ID: PCI_DEVICE TYPE: BC
> >PMGR: PCI_DEVICE_MGR PMGRPRI:
> 2
> >LMGR: MAXIOS:
> 0
> >
> >PATH: 0/0/2/0 LDEV:
> > ID: A5150A TYPE: DA
> >PMGR: PCI_SCSI_DAM PMGRPRI:
> 6
> >LMGR: MAXIOS:
> 0
> >
> >PATH: 0/0/2/0.5 LDEV:
> > ID: PSEUDO TYPE: DA
> >PMGR: TRANSPARENT_MGR PMGRPRI:
> 6
> >LMGR: MAXIOS:
> 0
> >
> >PATH: 0/0/2/0.5.0 LDEV:
> 9
> > ID: HP7980S TYPE:
> TAPE
> >PMGR: SCSI_TAPE2_DM PMGRPRI:
> 10
> >LMGR: LOGICAL_DEVICE_MANAGER MAXIOS:
> 0
> >
> >
> >--
> >Jim Alexander Longs Drug Stores
> >Sr. Systems Programmer 925-210-6901
> >The opinions expressed are Mine and not Longs Drugs
> >
> >
> >
> >-----Original Message-----
> >From: HP-3000 Systems Discussion
> [mailto:[log in to unmask]] On Behalf
> >Of Craig Lalley
> >Sent: Thursday, April 30, 2009 2:00 PM
> >To: [log in to unmask]
> >Subject: Re: [HP3000-L] Mpe: HP7980S Configuration on
> A400 - mapper2 output
> >
> >Karsten,
> >
> >It appears you are trying to use a dual-headed card in
> an A-class.
> >
> >I believe the A5150A is a dual port SCSI controller.
> It is not supported
> >in an A-class MPE configuration. There is no driver
> for it.
> >
> >Sorry,
> >
> >-Craig
> >
> >
> >
> >--- On Thu, 4/30/09, Karsten Brøndum
> <[log in to unmask]> wrote:
> >
> > > From: Karsten Brøndum <[log in to unmask]>
> > > Subject: Re: Mpe: HP7980S Configuration on A400 -
> mapper2 output
> > > To: [log in to unmask]
> > > Cc: [log in to unmask]
> > > Date: Thursday, April 30, 2009, 3:32 PM
> > > Booting...
> > > Boot IO Dependent Code (IODC) revision 1
> > >
> > > HARD Booted.
> > > MMSAVE Version 2.5
> > > DUMPAREA found, save main memory to disc
> > > ISL loaded
> > >
> > > ISL Revision A.00.43 Apr 12, 2000
> > >
> > >
> ***************************************************************************
> > > ******
> > > ******
> > > ****** Offline Diagnostic Environment
> > > ******
> > > ******
> > > ******
> > > ****** (C) Copyright Hewlett-Packard Co
> 1993-2000
> > > ******
> > > ****** All Rights Reserved
> > > ******
> > > ******
> > > ******
> > > ****** HP shall not be liable for any damages
> resulting
> > > from the ******
> > > ****** use of this program.
> > > ******
> > > ******
> > > ******
> > > ****** TC Version A.02.22
> > > ******
> > > ****** SysLib Version A.00.75
> > > ******
> > > ****** Loader Version A.00.61
> > > ******
> > > ****** Mapfile Version A.01.27
> > > ******
> > > ******
> > > ******
> > >
> ***************************************************************************
> > >
> > > Type HELP for command information.
> > >
> > >
> ***************************************************************************
> > > ******
> > > ******
> > > ****** MAPPER2
> > > ******
> > > ******
> > > ******
> > > ****** Copyright (C) 1998-2000 by
> Hewlett-Packard
> > > Company ******
> > > ****** All Rights Reserved
> > > ******
> > > ******
> > > ******
> > > ****** HP shall not be liable for any damages
> resulting
> > > from the ******
> > > ****** use of this program.
> > > ******
> > > ******
> > > ******
> > > ****** Version B.00.17
> > > ******
> > > ******
> > > ******
> > >
> ***************************************************************************
> > >
> > > Type HELP for command information.
> > >
> > >
> > > STARTING EXECUTION OF MAPPER2
> > >
> > > Processor Identification:
> > > Hardware Model: 5D6H, Revision: 0
> > > Software Model: 4H, Revision: 0
> > > Hardware ID: 0, Software ID: 1342988618
> (unsigned
> > > decimal)
> > > HP-UX Model String: 9000/800/A400-44
> > > MPE/XL Model String: e3000/A400-100-11#N
> > > Processor Board Revisions:
> > > CPU - CPU Chip: 768
> > > PDC - Processor Dependent Code: 41.10
> > > Cache and TLB Sizes:
> > > Instruction Cache: 512 K bytes,
> Instruction TLB:
> > > 160 entries
> > > Data Cache: 1024 K bytes, Data
> TLB:
> > > 160 entries
> > > Co-processors:
> > > Floating Point Co-processor(s) installed
> > >
> > > I/O Configuration:
> > >
> Type HW
> > > SW Revisions
> > > Path Component Name ID
> Model
> > > Model Hdwr Firm
> > > (77/124) Continue?
> > > ---------- -----------------------------------
> ----- -----
> > > ----- ----- -----
> > > 0 Astro BC Runway Port CH
> 582H
> > > BH 0 0
> > > 0/0 Elroy PCI Bridge DH
> 782H
> > > AH 0 0
> > > 0/0/0/0 Ethernet Controller
> 1011H 0019H
> > > 103CH 104FH 41H
> > > 0/0/1/0 SCSI Bus Controller
> 1000H 000BH
> > > 0000H 0000H 07H
> > > 0/0/1/1 SCSI Bus Controller
> 1000H 000BH
> > > 0000H 0000H 07H
> > > 0/0/1/1.15.0
> > > SEAGATE ST39204LC disk drive -
> - -
> > > - HP04
> > > 0/0/2/0 Symbios SCSI Controller
> 1000H 000FH
> > > 0000H 0000H 14H
> > > 0/0/2/0.5.0
> > > 7980S SCSI mag tape unit -
> - -
> > > - A731
> > > 0/0/2/1 Symbios SCSI Controller
> 1000H 000FH
> > > 0000H 0000H 14H
> > > 0/0/2/1.15.0
> > > SEAGATE ST318404LC disk drive -
> - -
> > > - HP04
> > > 0/0/4/0 Serial Controller
> 103CH 1048H
> > > 103CH 1049H 02H
> > > 0/0/5/0 Serial Controller
> 103CH 1048H
> > > 103CH 104AH 02H
> > > 0/2 Elroy PCI Bridge DH
> 782H
> > > AH 0 0
> > > 0/2/0/0 Ethernet Controller
> 1011H 0019H
> > > 103CH 1066H 41H
> > > 0/4 Elroy PCI Bridge DH
> 782H
> > > AH 0 0
> > > (96/124) Continue?
> > > 0/6 Elroy PCI Bridge DH
> 782H
> > > AH 0 0
> > > 8 Memory Controller (256 Mbytes) 1H
> 9BH
> > > 9H 0 0
> > > Slot 01 128M Active
> > > Slot 02 128M Active
> > > Slot 03 - -
> > > Slot 04 - -
> > > Slot 05 - -
> > > Slot 06 - -
> > > Slot 07 - -
> > > Slot 08 - -
> > > 160 Processor 0H
> 5D6H
> > > 4H 0 0
> > >
> > >
> > >
> > > Craig Lalley wrote:
> > > > Karsten,
> > > >
> > > > That's a good start. Every one has
> commented that
> > > the drive was seen in Mapper. Can you post the
> output from
> > > MAPPER2?
> > > >
> > > > -Craig
> > > >
> > > >
> > > >
> > > > --- On Thu, 4/30/09, Karsten Brøndum
> > > <[log in to unmask]> wrote:
> > > >
> > > >
> > > >> From: Karsten Brøndum
> <[log in to unmask]>
> > > >> Subject: Re: Mpe: HP7980S Configuration
> on A400
> > > >> To: [log in to unmask]
> > > >> Date: Thursday, April 30, 2009, 2:50 PM
> > > >> io>
> > > >> io> LP 0/0
> > > >> PATH: 0/0
> > > LDEV:
> > > >> ID: PAT_PCI_BC
> TYPE:
> > > BC
> > > >> PMGR: PCI_ELROY_MGR
> > > PMGRPRI: 2
> > > >> LMGR:
> > > MAXIOS: 0
> > > >>
> > > >> io> lp 0/0/2
> > > >> PATH: 0/0/2
> > > LDEV:
> > > >> ID: PCI_DEVICE
> TYPE:
> > > BC
> > > >> PMGR: PCI_DEVICE_MGR
> > > PMGRPRI: 2
> > > >> LMGR:
> > > MAXIOS: 0
> > > >>
> > > >> io> lp 0/0/2/0
> > > >> PATH: 0/0/2/0
> > > LDEV:
> > > >> ID: A5150A
> TYPE:
> > > DA
> > > >> PMGR: PCI_SCSI_DAM
> > > PMGRPRI: 6
> > > >> LMGR:
> > > MAXIOS: 0
> > > >>
> > > >> io>
> > > >>
> > > >> Thanks,
> > > >> Karsten.
> > > >>
> > > >> Gilles Schipper wrote:
> > > >>
> > > >>> Can you show us, in sysgen, io
> > > >>>
> > > >>> lp 0/0
> > > >>> lp 0/0/2
> > > >>> lp 0/0/2/0
> > > >>>
> > > >>> At 08:51 AM 2009-04-30, SUBSCRIBE
> HP3000-L
> > > Karsten
> > > >>>
> > > >> Brondum wrote:
> > > >>
> > > >>>> Trying to configure an HP7980S
> on A400,
> > > but
> > > >>>>
> > > >> receive
> > > >>
> > > >>>> LLIO Device configuration
> Error -11
> > > >>>>
> > > >>>> ODE / mapper 2 reports HP7980S
> on
> > > /0/0/2/0.5.0
> > > >>>>
> > > >> which matches path printed
> > > >>
> > > >>>> on back of A400. Did the
> following
> > > configuration:
> > > >>>>
> > > >>>> AP PATH=0/0/2/0.5;ID=PSEUDO
> > > >>>> AD 9;PATH=0/0/2/0.5.0;ID=HP7980S
> > > >>>>
> > > >>>> io> LD 9
> > > >>>> LDEV: 9 DEVNAME:
> > > OUTDEV:
> > > >> 0 MODE:
> > > >>
> > > >>>> ID: HP7980S
> > > RSIZE:
> > > >> 128 DEVTYPE: TAPE
> > > >>
> > > >>>> PATH: 0/0/2/0.5.0
> > > MPETYPE:
> > > >>>>
> > > >> 24 MPESUBTYPE: 5
> > > >>
> > > >>>> CLASS: TAPE
> > > >>>>
> > > >>>> :SHOWME
> > > >>>> USER: #S2,MANAGER.SYS,PUB
> (NOT IN
> > > BREAK)
> > > >>>> RELEASE: C.70.00 MPE/iX
> HP31900 C.39.06
> > > USER
> > > >>>>
> > > >> VERSION: C.70.00
> > > >>
> > > >>>> CURRENT: THU, APR 30, 2009,
> 2:48 PM
> > > >>>> LOGON: THU, APR 30, 2009,
> 2:39 PM
> > > >>>>
> > > >>>>
> > > >>>> Any help greatly appreciated
> > > >>>> Karsten.
> > > >>>>
> > > >>>> * To join/leave the list, search
> archives,
> > > change
> > > >>>>
> > > >> list settings, *
> > > >>
> > > >>>> * etc., please visit
> > > >>>>
> > > >>
> http://raven.utc.edu/archives/hp3000-l.html *
> > > >>
> > > >>>> No virus found in this incoming
> message.
> > > >>>> Checked by AVG - www.avg.com
> > > >>>> Version: 8.5.285 / Virus
> Database:
> > > 270.12.10/2088
> > > >>>>
> > > >> - Release Date: 04/30/09 06:01:00
> > > >>
> > > >>>
> > > >>
> > >
> >
> -------------------------------------------------------------------------------------------------
> > > >>
> > > >>
> > > >>> Gilles Schipper
> > > >>> GSA Inc.
> > > >>> HP System Administration Specialists
> > > >>> 300 John Street, Box 87651
> Thornhill, ON
> > > Canada L3T
> > > >>>
> > > >> 7R4
> > > >>
> > > >>> Voice: 905.889.3000 Fax:
> 905.889.3001
> > > >>> email: [log in to unmask] web:
> > > http://www.gsainc.com
> > > >>>
> > > >>>
> > > >>
> > >
> >
> -------------------------------------------------------------------------------------------------
> > > >>
> > > >>
> > > >>>
> > > >>>
> > > >>>
> > > >> * To join/leave the list, search
> archives, change
> > > list
> > > >> settings, *
> > > >> * etc., please visit
> > > >>
> http://raven.utc.edu/archives/hp3000-l.html *
> > > >>
> > > >
> > > >
> > > >
> >
> >* To join/leave the list, search archives, change list
> settings, *
> >* etc., please visit
> http://raven.utc.edu/archives/hp3000-l.html *
> >
> >* To join/leave the list, search archives, change list
> settings, *
> >* etc., please visit
> http://raven.utc.edu/archives/hp3000-l.html *
> >
> >
> >
> >--
> >No virus found in this incoming message.
> >Checked by AVG.
> >Version: 7.5.557 / Virus Database: 270.12.10/2088 -
> Release Date: 4/30/09
> >6:01 AM
>
> * To join/leave the list, search archives, change list
> settings, *
> * etc., please visit
> http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
