I tried to load an old Micro/XE but kept having
problems. I got the new tapes from HP this Winter,
and mounted them on my HP7974.
I got the tape to BOT, (even though self-test on
power up ended on F.50)
I turned on the Micro/XE and I get the following,
note the various gyrations that I tried. Any ideas?
----
Power on Self Test
Cache Test passed
Memory Test passed
Memory Size (MEGABYTES) = 06
Slot 1 Channel 1 - Terminal Interface Controller
Slot 4 Channel 4 - Peripheral Interface Channel
Slot E4 Channel 12 - Terminal Interface Controller
Slot E5 Channel 13 - Terminal Interface Controller
1-NORMAL
H for help->h
mainset microcode is NOT loaded
Auto warmstart disabled
Cache enabled
last system stop code (hex)=00FD
AR - Re-attempt Auto Restart, NEW[system],
COL[dstart], PA[nel] - Enter soft-panel,
COO[lstart], REL[oad],
DC - Disable Cache, RUN,
DI[sc] - Start from Disc, SP[eed],
DU[mp] [chan, dev], ST[art] [chan, dev[,?P[erm] ]],
DW - Disable Auto Warmstart, C[hange]?
EC - Enable Cache, TA[pe] - Load from Tape,
EW - Enable Auto Warmstart, TE[st],
L[oad] [chan, dev[,?P[erm] ]], UPD[ate],
C[hange]? WAR[mstart]
1-NORMAL
H for help->PA
SoftPanel - V3.3 11/07/84
Cache enabled
SP> H
THERE IS NO BLANK EATER! Syntax is exact
== means is defined to be, [] denote an optional field,
?? denote items, one of which must be selected, | means or
<modifier> == <expr>[:[[+|-]<expr>]]
<expr> == <numeric>[?+|-|*?<expr>]
DA <modifier>[,<count>]
MA <modifier>
DEA <bank>.<modifier>[,<count>]
MEA <bank>.<modifier>
Dxx[?+|-| ?<modifier>[,<count>] <- Display Memory
Mxx[?+|-| ?<modifier> <- Modify Memory
where xx is SY, DB, DL, Z, Q, S, PB, P, or PL
D <- continue display
DR [<reg>]
MR <reg>
<reg> maybe:
DB, DL, Q, S, PB, P, PL, Z, STA, SB, CIR, X, SW
Dbank, Sbank, Pbank, LPFlg, Disp, or ICS
DR [<regfile>[,<count>]]
MR <regfile>
Modifies (MR and Mxx [above]) are terminated with '.' or '/'
RTOC <TOCaddr> <- Reads TOC address
WTOC <TOCaddr>,<data> <- writes data to TOC address
E <- exit to Maint Mode
RUN <- resume software execution
RIO <ioaddr> read/write io address
WIO <ioaddr>,<iodata>
T [[<bank>.]<numeric>] walk stack
ENV <numeric> back up markers
RDX [H|O] change/display default Radix
ST softpanel status info
SMB [A:|B:]<bank>.<expr>[,?RD|WR?][,RA] set memory break point
RD = read only, WR = write only, RA = enable range mode
SMD <data pattern> set memory break data pattern
CMB clears all memory breakpoints
SB show breakpoints
'?' or 'H' display this message
SP> E
1-NORMAL
H for help->DC
Cache disabled
1-NORMAL
H for help->DW
Auto warmstart disabled
1-NORMAL
H for help->L
WCS Boot failure:
Can't read WCS pointer record from tape
[I switched keys here.]
2-LOCAL (from Normal)
H for help->L 4,3
WCS Boot failure:
Can't read WCS pointer record from tape
2-LOCAL (from Normal)
H for help->NEW
WCS Boot failure:
Can't read WCS pointer record from tape
[Switched keys again.]
3-REMOTE
H for help->TA
WCS Boot failure:
Can't read WCS pointer record from tape
3-REMOTE
H for help->TE
ROM Version: 2640
Selftest Menu:
AL[l] [ count ]
CA[che] [ count [ ,section [ ,mode ] ] ]
CH[an] [ count [ ,chan ] ]
CP[u] [ count ]
E[xit]
I[omap] [ count ]
M[emory] [ count ]
PON [ count ]
3-REMOTE
Test ->AL
TOC RAM
Addr Data
000E 0045
000F 0000
0010 00FD
0011 0021
0012 0023
0013 0004
0014 0000
0015 0000
Observe LED display cycle 0-F
CPU test passed
Memory Test passed
Cache Test passed
Cannot test console TIC in REMOTE or LOCAL(from REMOTE)
Slot 4 Channel 4 - Peripheral Interface Channel
Slot E4 Channel 12 - Terminal Interface Controller
Slot E5 Channel 13 - Terminal Interface Controller
Test Passed
System I/O Configuration
----------------------------------------------------------------------
Memory Size (MEGABYTES) = 06
Load: Channel 4 Device 3
Start/Dump: Channel 4 Device 1
----------------------------------------------------------------------
Slot 1 Channel 1 ID=4 - Terminal Interface Controller
----------------------------------------------------------------------
Slot 4 Channel 4 ID=2 - Peripheral Interface Channel
Device 0 ID=0214 - 7937 Disc drive
Device 1 ID=0214 - 7937 Disc drive
Device 3 ID=0174 - 7974 Mag Tape Unit
----------------------------------------------------------------------
Slot E4 Channel 12 ID=4 - Terminal Interface Controller
----------------------------------------------------------------------
Slot E5 Channel 13 ID=4 - Terminal Interface Controller
----------------------------------------------------------------------
3-REMOTE
Test ->E
3-REMOTE
H for help->L
WCS Boot failure:
Can't read WCS pointer record from tape
3-REMOTE
H for help->NEW
WCS Boot failure:
Can't read WCS pointer record from tape
3-REMOTE
H for help->TA
WCS Boot failure:
Can't read WCS pointer record from tape
3-REMOTE
H for help->L 4,3
WCS Boot failure:
Can't read WCS pointer record from tape
3-REMOTE
H for help->L 4,3
WCS Boot failure:
Can't read WCS pointer record from tape
|
