I wonder why the install is saying it cannot access 56/52.5 then...
>
> > I got the messages
> >
> > Can't access disk at 56/52.5.0 ....
> > System Abort 55 from Syb System 146
> > Sec Status: info -31281, Subsystem = 213 System Halt 7, $0037
Ryan C. Melander
Ideal Computer Services, Inc.
88 Wright Brothers Ave.
Livermore, CA 94551
Ph. 800-862-8787
Ph. 925-447-4747 x213
Fx. 925-447-4780
mailto:[log in to unmask]
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of Mark Landin
Sent: Wednesday, February 23, 2011 3:26 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Replacement of SE Scsi to DF Scsi Storage.
No guys, look: his path for his NEW disk is 56/36.5. His pri path is set to 56/52.6. INSTALL can't find the primary path to install anything on! he has to set his PRI path to 56/36.5.
On Wed, Feb 23, 2011 at 5:05 PM, Ryan C. Melander <[log in to unmask]>wrote:
> If your disk are the same address as the old ones. .5 and .6 and the
> system
> reports: > Can't access disk at 56/52.5.0 .... your primary boot
> path is
> 56/52.5 (normally it should be 56/52.60 but that's ok) I would say
> you either have another bad disk at 56/52.5 or your SCSI address
> jumpers are wrong.
>
> Ryan
>
>
> Ryan C. Melander
> Ideal Computer Services, Inc.
> 88 Wright Brothers Ave.
> Livermore, CA 94551
> Ph. 800-862-8787
> Ph. 925-447-4747 x213
> Fx. 925-447-4780
> mailto:[log in to unmask]
>
>
> -----Original Message-----
> From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On
> Behalf Of Paul Edwards
> Sent: Wednesday, February 23, 2011 2:59 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Replacement of SE Scsi to DF Scsi Storage.
>
> Did you set the SCSI address correctly on the new drive?
>
> ***************************************************************
> CDR Paul Edwards USNR Ret. HP 3000 Certified Consultant
> Paul Edwards & Associates
> 1506 Estates Way Phone: (972) 242-6660
> Carrollton TX 75006 Cel : (214) 384-8728
> Email: [log in to unmask] Web : www.peassoc.com
> ***************************************************************
>
>
> -----Original Message-----
> From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On
> Behalf Of Harpreet SINGH
> Sent: Wednesday, February 23, 2011 4:48 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Replacement of SE Scsi to DF Scsi Storage.
>
> Hi,
>
> But I am replacing the disk one to one.
>
> With Warm Regards
> =-=-=-=-=-=-=-=-=-=-=-=-=-
> Harpreet Singh Chana
>
> Phone : (O) 6895 - 4326
> Fax : (O) 6895 - 4991
> =-=-=-=-=-=-=-=-=-=-=-=-=-
> Please do not print this email unless it is absolutely necessary.
>
>
> Notice
> The information in this message is confidential and may be legally
> privileged. It is intended solely for the addressee. Access to this
> message by anyone else is unauthorized. If you are not the intended
> recipient, any disclosure, copying or distribution of the message,
> or any action taken by you in reliance on it, is prohibited and may
> be unlawful.
> If you have received this message in error, please delete it and
> contact the sender immediately. Thank you.
>
>
>
>
>
> Mark Landin
> <marklandin@GMAIL
> .COM> To
> Sent by: HP-3000 [log in to unmask]
> Systems cc
> Discussion
> <[log in to unmask] Subject
> TC.EDU <http://tc.edu/>> Re: [HP3000-L]
> Replacement of SE
> Scsi to DF Scsi Storage.
>
> 02/24/2011 06:11
> AM
>
>
>
> Please respond to
> Mark Landin
> <marklandin@GMAIL
> .COM>
>
>
>
>
>
>
> When you replaced the disk drives, notice how their hardware path changed.
>
> Now check what your PRI boot path is. that's where the CSLT will try
> to install things. You will need to change your PRI boot path to the
> hardware path of one of the new disks you put in. This will become LDEV 1.
>
> On Wed, Feb 23, 2011 at 2:58 PM, Harpreet SINGH <
> [log in to unmask]> wrote:
>
> > Hi,
> >
> > I have managed to verify the CSLT Tape on working server and found
> > no errors.
> >
> > I have taken out this working Tape drive from the working server in
> > Replaced with the suspected faulty Tape drive.
> >
> > -- On server Side I have inserted two Disk in the disk enclosure.
> > -- Restart the Server
> > -- Search for the Hardware
> > -- I found 3 devices
> > i.e.
> > -- P0 56/36.5 DISK
> > --P1 56/36.6 DISK
> > --P2 56/52/0 TAPE
> >
> > So I boot the server with bo p2
> > Interact with IPL = N
> >
> > ISL > Install
> >
> > I got the messages
> >
> > Can't access disk at 56/52.5.0 ....
> > System Abort 55 from Syb System 146
> > Sec Status: info -31281, Subsystem = 213 System Halt 7, $0037
> > --
> > "He's old enough to know what's right and young enough not to choose it.
> > He's strong enough to win the world and weak enough to lose it." -
> > Neal Peart
> >
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
> ForwardSourceID:NT0019F97A
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
--
"He's old enough to know what's right and young enough not to choose it.
He's strong enough to win the world and weak enough to lose it." - Neal Peart
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|