John-
1) Make sure he shows up with a Torx set. ;-)
2) Make sure he does not bend any pins on the internal scsi ribbon
cable.
3) SCSI ID 0 on that DDS-3 : all jumpers open
Best regards,
Lawrence Kaufman
Systems Engineer / Analyst
Weltman, Weinberg & Reis Co., LPA
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On
Behalf Of John Pitman
Sent: Sunday, November 06, 2011 11:17 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] sysgen io info vs cstm->map info
Thanks.
I am trying to avoid having to guide somebody with poor English through
ODE and mapper and back out again. I hope that if they install a new
drive and reboot, and can see the tape part no with same scsi address as
before , it should be good. I will also get them to test reading an old
tape, and writing a new one before tech leaves the scene....
Regards,
John Pitman
-----Original Message-----
From: Gilles Schipper [mailto:[log in to unmask]]
Sent: Monday, 7 November 2011 2:43 PM
To: John Pitman; [log in to unmask]
Subject: Re: [HP3000-L] sysgen io info vs cstm->map info
Those aren't ldev's that cstm is showing - they're simply numerical
instances.
The scsi address of ldev 7 is defintely 0 - as shown by sysgen and cstm.
At 10:33 PM 2011-11-06, John Pitman wrote:
>On one of our 959s, sysgen for tape drive shows:
>
> io> ldev 7
>LDEV: 7 DEVNAME: OUTDEV: 0 MODE:
R
> ID: HPC1537A RSIZE: 128 DEVTYPE:
TAPE
> PATH: 10/4/20.0.0 MPETYPE: 24
MPESUBTYPE: 7
>CLASS: TAPE
>
>But cstm->map shows:-
>
> 1 10 Bus Adapter (580)
> 2 10/4 Bus Adapter (500)
> 3 10/4/0 NIO LAN/Console Interface
> 4 10/4/16 100 BaseT LAN Interface (
> 5 10/4/20 NIO SCSI Interface (5)
> 6 10/4/20.0.0 SCSI Tape (HPC1537A)
> 7 10/4/20.2 Unknown ()
> 8 10/4/20.8.0 Unknown ()
> 9 10/4/20.9.0 Unknown ()
> 10 10/4/24 NIO Fast/Wide SCSI Interf
> 11 10/4/24.5.0 SCSI Disk (SEAGATEST39175
> 12 10/4/24.6.0 SCSI Disk (SEAGATEST39175
>
>Does this mean the SCSI address of the tape drive is 0, or 2 ? the 0
>addr shows on ldev 6, but 2 on ldev 7 ????
>
>I suspect the devnums on the left in cstm are wrong, as they list the
>discs at 11 and 12, not 1 and 2.
>Unfortunately the people replacing the dead dds3 drive are not famous
>for their knowledge of mpe, so I am trying to ensure they get it right
>first time. I hope just telling them to configure all dip switches same
>as old unit will work for us.
>
>Regards,
>
>John Pitman
>
>
>________________________________
>CAUTION: This message may contain privileged and confidential
>information intended only for the use of the addressee named above.
>If you are not the intended recipient of this message you are hereby
>notified that any use, dissemination, distribution or reproduction of
>this message is prohibited. If you have received this message in error
>please notify RYCO Hydraulics Pty. Ltd. immediately. Any views
>expressed in this message are those of the individual sender and may
>not necessarily reflect the views of RYCO Hydraulics Pty. Ltd.
>
>* To join/leave the list, search archives, change list settings, *
>* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
------------------------------------------------------------------------
-------------------------
Gilles Schipper
GSA Inc.
HP System Administration Specialists
300 John Street, Box 87651 Thornhill, ON Canada L3T 7R4
Tel: 416.702.7900
email: [log in to unmask] web: http://www.gsainc.com
------------------------------------------------------------------------
-------------------------
CAUTION: This message may contain privileged and confidential
information intended only for the use of the addressee named above. If
you are not the intended recipient of this message you are hereby
notified that any use, dissemination, distribution or reproduction of
this message is prohibited. If you have received this message in error
please notify RYCO Hydraulics Pty. Ltd. immediately. Any views expressed
in this message are those of the individual sender and may not
necessarily reflect the views of RYCO Hydraulics Pty. Ltd.
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
