Jim,
http://www.docs.hp.com/en/30216-90336/ch05s05.html
Look at table 5-2 Interface cards...
A-Class Core I/O
VHDCI 68-pin LVD/SE SCSI Internal LVD/SE SCSI*
HD 50-pin SE-SCSI **
Internal LVD/SE SCSI*
** This connection exclusively supports 8-bit wide SCSI transfers. Therefore only DDS3 and 7980 Tape Devices are supported; other devices will not function or will loose data.
So it looks like the A5149A WON't work.
Where's the HD 50-pin SE-SCSI connector?? I don't have an A-class in front of me. Can someone go look?
-Craig
--- On Thu, 4/30/09, Jim Alexander <[log in to unmask]> wrote:
> From: Jim Alexander <[log in to unmask]>
> Subject: Re: Mpe: HP7980S Configuration on A400 - mapper2 output
> To: [log in to unmask]
> Date: Thursday, April 30, 2009, 4:08 PM
> I guess that means the one in the A500 that we have at Longs
> doesn't work.
>
> Hmm .. Guess, I should tell that A-class box, since it has
> worked since we installed in about 2003 ... Probably
> because it just doesn't know any better.
>
> From our System config:
>
> A500-200-140 IXH - MPE Test & Development System
>
> And
>
> PATH: 0/0/2 LDEV:
> ID: PCI_DEVICE TYPE: BC
> PMGR: PCI_DEVICE_MGR PMGRPRI: 2
> LMGR: MAXIOS: 0
>
> PATH: 0/0/2/0 LDEV:
> ID: A5150A TYPE: DA
> PMGR: PCI_SCSI_DAM PMGRPRI: 6
> LMGR: MAXIOS: 0
>
> PATH: 0/0/2/0.5 LDEV:
> ID: PSEUDO TYPE: DA
> PMGR: TRANSPARENT_MGR PMGRPRI: 6
> LMGR: MAXIOS: 0
>
> PATH: 0/0/2/0.5.0 LDEV: 9
> ID: HP7980S TYPE: TAPE
> PMGR: SCSI_TAPE2_DM PMGRPRI: 10
> LMGR: LOGICAL_DEVICE_MANAGER MAXIOS: 0
>
>
> --
> Jim Alexander Longs Drug Stores
> Sr. Systems Programmer 925-210-6901
> The opinions expressed are Mine and not Longs Drugs
>
>
>
> -----Original Message-----
> From: HP-3000 Systems Discussion
> [mailto:[log in to unmask]] On Behalf Of Craig Lalley
> Sent: Thursday, April 30, 2009 2:00 PM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Mpe: HP7980S Configuration on A400
> - mapper2 output
>
> Karsten,
>
> It appears you are trying to use a dual-headed card in an
> A-class.
>
> I believe the A5150A is a dual port SCSI controller. It is
> not supported in an A-class MPE configuration. There is no
> driver for it.
>
> Sorry,
>
> -Craig
>
>
>
> --- On Thu, 4/30/09, Karsten Brøndum
> <[log in to unmask]> wrote:
>
> > From: Karsten Brøndum <[log in to unmask]>
> > Subject: Re: Mpe: HP7980S Configuration on A400 -
> mapper2 output
> > To: [log in to unmask]
> > Cc: [log in to unmask]
> > Date: Thursday, April 30, 2009, 3:32 PM
> > Booting...
> > Boot IO Dependent Code (IODC) revision 1
> >
> > HARD Booted.
> > MMSAVE Version 2.5
> > DUMPAREA found, save main memory to disc
> > ISL loaded
> >
> > ISL Revision A.00.43 Apr 12, 2000
> >
> >
> ***************************************************************************
> > ******
>
> > ******
> > ****** Offline Diagnostic Environment
>
> > ******
> > ******
>
> > ******
> > ****** (C) Copyright Hewlett-Packard Co 1993-2000
>
> > ******
> > ****** All Rights Reserved
>
> > ******
> > ******
>
> > ******
> > ****** HP shall not be liable for any damages
> resulting
> > from the ******
> > ****** use of this program.
>
> > ******
> > ******
>
> > ******
> > ****** TC Version A.02.22
>
> > ******
> > ****** SysLib Version A.00.75
>
> > ******
> > ****** Loader Version A.00.61
>
> > ******
> > ****** Mapfile Version A.01.27
>
> > ******
> > ******
>
> > ******
> >
> ***************************************************************************
> >
> > Type HELP for command information.
> >
> >
> ***************************************************************************
> > ******
>
> > ******
> > ****** MAPPER2
>
> > ******
> > ******
>
> > ******
> > ****** Copyright (C) 1998-2000 by
> Hewlett-Packard
> > Company ******
> > ****** All Rights Reserved
>
> > ******
> > ******
>
> > ******
> > ****** HP shall not be liable for any damages
> resulting
> > from the ******
> > ****** use of this program.
>
> > ******
> > ******
>
> > ******
> > ****** Version B.00.17
>
> > ******
> > ******
>
> > ******
> >
> ***************************************************************************
> >
> > Type HELP for command information.
> >
> >
> > STARTING EXECUTION OF MAPPER2
> >
> > Processor Identification:
> > Hardware Model: 5D6H, Revision: 0
> > Software Model: 4H, Revision: 0
> > Hardware ID: 0, Software ID: 1342988618 (unsigned
> > decimal)
> > HP-UX Model String: 9000/800/A400-44
> > MPE/XL Model String: e3000/A400-100-11#N
> > Processor Board Revisions:
> > CPU - CPU Chip: 768
> > PDC - Processor Dependent Code: 41.10
> > Cache and TLB Sizes:
> > Instruction Cache: 512 K bytes, Instruction
> TLB:
> > 160 entries
> > Data Cache: 1024 K bytes, Data TLB:
>
> > 160 entries
> > Co-processors:
> > Floating Point Co-processor(s) installed
> >
> > I/O Configuration:
> > Type HW
>
> > SW Revisions
> > Path Component Name ID
> Model
> > Model Hdwr Firm
> > (77/124) Continue?
> > ---------- ----------------------------------- -----
> -----
> > ----- ----- -----
> > 0 Astro BC Runway Port CH
> 582H
> > BH 0 0
> > 0/0 Elroy PCI Bridge DH
> 782H
> > AH 0 0
> > 0/0/0/0 Ethernet Controller 1011H
> 0019H
> > 103CH 104FH 41H
> > 0/0/1/0 SCSI Bus Controller 1000H
> 000BH
> > 0000H 0000H 07H
> > 0/0/1/1 SCSI Bus Controller 1000H
> 000BH
> > 0000H 0000H 07H
> > 0/0/1/1.15.0
> > SEAGATE ST39204LC disk drive - -
> -
> > - HP04
> > 0/0/2/0 Symbios SCSI Controller 1000H
> 000FH
> > 0000H 0000H 14H
> > 0/0/2/0.5.0
> > 7980S SCSI mag tape unit - -
> -
> > - A731
> > 0/0/2/1 Symbios SCSI Controller 1000H
> 000FH
> > 0000H 0000H 14H
> > 0/0/2/1.15.0
> > SEAGATE ST318404LC disk drive - -
> -
> > - HP04
> > 0/0/4/0 Serial Controller 103CH
> 1048H
> > 103CH 1049H 02H
> > 0/0/5/0 Serial Controller 103CH
> 1048H
> > 103CH 104AH 02H
> > 0/2 Elroy PCI Bridge DH
> 782H
> > AH 0 0
> > 0/2/0/0 Ethernet Controller 1011H
> 0019H
> > 103CH 1066H 41H
> > 0/4 Elroy PCI Bridge DH
> 782H
> > AH 0 0
> > (96/124) Continue?
> > 0/6 Elroy PCI Bridge DH
> 782H
> > AH 0 0
> > 8 Memory Controller (256 Mbytes) 1H
> 9BH
> > 9H 0 0
> > Slot 01 128M Active
> > Slot 02 128M Active
> > Slot 03 - -
> > Slot 04 - -
> > Slot 05 - -
> > Slot 06 - -
> > Slot 07 - -
> > Slot 08 - -
> > 160 Processor 0H
> 5D6H
> > 4H 0 0
> >
> >
> >
> > Craig Lalley wrote:
> > > Karsten,
> > >
> > > That's a good start. Every one has commented
> that
> > the drive was seen in Mapper. Can you post the output
> from
> > MAPPER2?
> > >
> > > -Craig
> > >
> > >
> > >
> > > --- On Thu, 4/30/09, Karsten Brøndum
> > <[log in to unmask]> wrote:
> > >
> > >
> > >> From: Karsten Brøndum <[log in to unmask]>
> > >> Subject: Re: Mpe: HP7980S Configuration on
> A400
> > >> To: [log in to unmask]
> > >> Date: Thursday, April 30, 2009, 2:50 PM
> > >> io>
> > >> io> LP 0/0
> > >> PATH: 0/0
> > LDEV:
> > >> ID: PAT_PCI_BC
> TYPE:
> > BC
> > >> PMGR: PCI_ELROY_MGR
> > PMGRPRI: 2
> > >> LMGR:
> > MAXIOS: 0
> > >>
> > >> io> lp 0/0/2
> > >> PATH: 0/0/2
> > LDEV:
> > >> ID: PCI_DEVICE
> TYPE:
> > BC
> > >> PMGR: PCI_DEVICE_MGR
> > PMGRPRI: 2
> > >> LMGR:
> > MAXIOS: 0
> > >>
> > >> io> lp 0/0/2/0
> > >> PATH: 0/0/2/0
> > LDEV:
> > >> ID: A5150A
> TYPE:
> > DA
> > >> PMGR: PCI_SCSI_DAM
> > PMGRPRI: 6
> > >> LMGR:
> > MAXIOS: 0
> > >>
> > >> io>
> > >>
> > >> Thanks,
> > >> Karsten.
> > >>
> > >> Gilles Schipper wrote:
> > >>
> > >>> Can you show us, in sysgen, io
> > >>>
> > >>> lp 0/0
> > >>> lp 0/0/2
> > >>> lp 0/0/2/0
> > >>>
> > >>> At 08:51 AM 2009-04-30, SUBSCRIBE
> HP3000-L
> > Karsten
> > >>>
> > >> Brondum wrote:
> > >>
> > >>>> Trying to configure an HP7980S on
> A400,
> > but
> > >>>>
> > >> receive
> > >>
> > >>>> LLIO Device configuration Error -11
> > >>>>
> > >>>> ODE / mapper 2 reports HP7980S on
> > /0/0/2/0.5.0
> > >>>>
> > >> which matches path printed
> > >>
> > >>>> on back of A400. Did the following
> > configuration:
> > >>>>
> > >>>> AP PATH=0/0/2/0.5;ID=PSEUDO
> > >>>> AD 9;PATH=0/0/2/0.5.0;ID=HP7980S
> > >>>>
> > >>>> io> LD 9
> > >>>> LDEV: 9 DEVNAME:
>
> > OUTDEV:
> > >> 0 MODE:
> > >>
> > >>>> ID: HP7980S
>
> > RSIZE:
> > >> 128 DEVTYPE: TAPE
> > >>
> > >>>> PATH: 0/0/2/0.5.0
>
> > MPETYPE:
> > >>>>
> > >> 24 MPESUBTYPE: 5
> > >>
> > >>>> CLASS: TAPE
> > >>>>
> > >>>> :SHOWME
> > >>>> USER: #S2,MANAGER.SYS,PUB (NOT
> IN
> > BREAK)
> > >>>> RELEASE: C.70.00 MPE/iX HP31900
> C.39.06
> > USER
> > >>>>
> > >> VERSION: C.70.00
> > >>
> > >>>> CURRENT: THU, APR 30, 2009, 2:48 PM
> > >>>> LOGON: THU, APR 30, 2009, 2:39 PM
> > >>>>
> > >>>>
> > >>>> Any help greatly appreciated
> > >>>> Karsten.
> > >>>>
> > >>>> * To join/leave the list, search
> archives,
> > change
> > >>>>
> > >> list settings, *
> > >>
> > >>>> * etc., please visit
> > >>>>
> > >> http://raven.utc.edu/archives/hp3000-l.html *
> > >>
> > >>>> No virus found in this incoming
> message.
> > >>>> Checked by AVG - www.avg.com
> > >>>> Version: 8.5.285 / Virus Database:
> > 270.12.10/2088
> > >>>>
> > >> - Release Date: 04/30/09 06:01:00
> > >>
> > >>>
> > >>
> >
> -------------------------------------------------------------------------------------------------
> > >>
> > >>
> > >>> Gilles Schipper
> > >>> GSA Inc.
> > >>> HP System Administration Specialists
> > >>> 300 John Street, Box 87651 Thornhill,
> ON
> > Canada L3T
> > >>>
> > >> 7R4
> > >>
> > >>> Voice: 905.889.3000 Fax: 905.889.3001
> > >>> email: [log in to unmask] web:
> > http://www.gsainc.com
> > >>>
> > >>>
> > >>
> >
> -------------------------------------------------------------------------------------------------
> > >>
> > >>
> > >>>
> > >>>
> > >>>
> > >> * To join/leave the list, search archives,
> change
> > list
> > >> settings, *
> > >> * etc., please visit
> > >> http://raven.utc.edu/archives/hp3000-l.html *
> > >>
> > >
> > >
> > >
>
> * To join/leave the list, search archives, change list
> settings, *
> * etc., please visit
> http://raven.utc.edu/archives/hp3000-l.html *
>
> * To join/leave the list, search archives, change list
> settings, *
> * etc., please visit
> http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
