Nope, definitely not in block mode.
On 7/8/10, Robert Schlosser <[log in to unmask]> wrote:
> Is the terminal in BLOCK MODE? It does not seem likely as you say it
> responds to ctrl-B, just a thought.
>
> Bob Schlosser
> Technical Consultant
> The Support Group
> Austin, TX
> (512) 284-3733 cell
> (512) 266-4400 office
> (800) 743-8142 Support
>
>
> CONFIDENTIAL: This message is intended only for the use of the individual
> to whom it is addressed. It contains information which may be privileged,
> confidential and exempt from disclosure under applicable law. Any views or
> opinions presented are solely those of the sender and do not necessarily
> represent those of Blanket Enterprises, Inc. or its subsidiaries unless
> otherwise specifically stated. If the reader of this message is not the
> intended recipient, the reader is hereby notified that any dissemination,
> distribution or copying of this communication is strictly prohibited. If
> you have received this communication in error, please inform the sender via
> email or call us at (800) 798-9862.
>
>
>
> -----Original Message-----
> From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf
> Of Mark Landin
> Sent: Thursday, July 08, 2010 9:43 AM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] Console not responding
>
> CTRL-Q had no effect either...
>
> On Thu, Jul 8, 2010 at 9:27 AM, Johnson, Tracy
> <[log in to unmask]>wrote:
>
>> Grabbing the console will have solved the old fashioned console buffer
>> problem. (At least the system isn't hung.)
>>
>> For giggles, have you tried a Control-Q?
>>
>>
>> Tracy Johnson
>> Office 1-757-766-4318
>> [log in to unmask]
>>
>>
>>
>>
>> ________________________________
>>
>> From: Mark Landin [mailto:[log in to unmask]]
>> Sent: Thursday, July 08, 2010 10:20 AM
>> To: Johnson, Tracy
>> Cc: [log in to unmask]
>> Subject: Re: [HP3000-L] Console not responding
>>
>>
>> - No replies pending on console.
>> - All volume sets and disk devices are available, healthy, and
>> not full.
>> - There is no active session on LDEV 20, but checking :SHOWDEV
>> again shows it as "UNAVAIL", by "SYS: #1". I did an ABORTIO on that LDEV
>> until it confirmed there was no more I/O..now the console will not
>> respond to a CRTL-A anymore, although it will to a CTRL-B.
>> - I swtiched the console to my device temporarily, and now
>> cannot switch console back to LDEV 20 as it says "Device is owned by
>> another process".
>>
>> We are on MPE/iX 6.5
>>
>> I expect we're going to schedule a reboot, but will probably
>> have to wait until the weekend.
>>
>>
>> On Thu, Jul 8, 2010 at 8:55 AM, Johnson, Tracy
>> <[log in to unmask]> wrote:
>>
>>
>> Any number of things.
>>
>> It could be in the middle of a program that is hung.
>> For any reason.
>>
>> It could be in the middle of a program waiting for a
>> REPLY, (Control-A,
>> RECALL may fix that.)
>>
>> You could be out of disc space. Which may be highly
>> likely if you had a
>> MOD 20 failure. A Volume_Set could be inadvertently
>> dismounted.
>> (Symptoms are similar to out of disc space conditions.)
>>
>> Tracy Johnson
>> Office 1-757-766-4318
>> [log in to unmask]
>>
>>
>>
>> > -----Original Message-----
>> > From: HP-3000 Systems Discussion
>> > [mailto:[log in to unmask]] On Behalf Of Mark
>> Landin
>> > Sent: Thursday, July 08, 2010 9:39 AM
>> > To: [log in to unmask]
>> > Subject: [HP3000-L] Console not responding
>> >
>>
>> > Hey folks.
>> >
>> > We have a 700/96 connected to our 939KS/020 as the
>> console.
>> > This morning, we
>> > can't get a login prompt on it. We can Ctrl-B just
>> fine, we
>> > see console
>> > messages, and showdev looks normal. We checked the
>> terminal
>> > and datacomm
>> > config ... all OK. We even hooked up another known
>> good
>> > 700/96, and get the
>> > same behavior.
>> >
>> > A bit of recent history ... we recently had an
>> overtemp
>> > condition in our
>> > machine room on Tuesday, and the system shut down. The
>> Model
>> > 20 we have
>> > connected wouldn't come back up until we replaced one
>> of the
>> > (supposedly
>> > redundant?) SP's, and then the machine seemed to boot
>> fine.
>> > It ran without
>> > incident the rest of Tuesday and all day yesterday.
>> >
>> > So, any ideas? I vaguely remember reading about
>> problems if
>> > the console
>> > buffer filled up, but don't recall any details,
>> especially
>> > how to clear that
>> > condition if, in fact, it exists.
>> >
>> > --
>> > "He's old enough to know what's right and young enough
>> not to
>> > choose it.
>> > He's strong enough to win the world and weak enough to
>> lose
>> > it." - Neal
>> > Peart
>> >
>>
>> > * To join/leave the list, search archives, change list
>> settings, *
>> > * etc., please visit
>> http://raven.utc.edu/archives/hp3000-l.html *
>> >
>>
>> * To join/leave the list, search archives, change list
>> settings, *
>> * etc., please visit
>> http://raven.utc.edu/archives/hp3000-l.html *
>>
>>
>>
>>
>>
>> --
>> "He's old enough to know what's right and young enough not to
>> choose it. He's strong enough to win the world and weak enough to lose
>> it." - Neal Peart
>>
>>
>>
>> * To join/leave the list, search archives, change list settings, *
>> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>>
>
>
>
> --
> "He's old enough to know what's right and young enough not to choose it.
> He's strong enough to win the world and weak enough to lose it." - Neal
> Peart
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
>
--
Sent from my mobile device
"He's old enough to know what's right and young enough not to choose
it. He's strong enough to win the world and weak enough to lose it." -
Neal Peart
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
