System Package option:
2 is for UNIX and A is for MPE

Bob J. -- Ideal Computer Services
http://www.icsgroup.net


Greg Terterian wrote:

>This is Dave Jack (greg is out on vacation in Armenia and I am stuck with this project... lol)
>
>Ok, here is the scoope.  the path is correct (primary and alternate).  ALl the drives on the NIKE is mirrored drives.  However, from the system disk (one of the drive is 4.0GB and the other one is 9.0GB) - All the other 5 mirrored drives are 9.0 gb
>When I do 'SEARCH' at the booth command it does display all of my scsi disk drives in correct order and with correct path.  When I do ODE MAPPER/RUN it does not display HPC2300WD, but instead it displays the actual disk drive names.  I double checked the system host interface type and it is set to 'B'.  Unless if this is wrong and this is where my problem is, I dont know where else to look for.
>My SYSGEN Tape is good, because I just made another one (and so far I tried at least 3 different SYSGEN tapes).  THE SCSI Card is the correct card and I did try 2 different SCSI cards already - both of them compatable with NIKE MOD20
>the system is 979/400 with MPE/iX 7.0
>
>Any help or direction will be appreciated!
>
>Thank you
>David Raschka
>
>
>
>
>
>
>
>-----Original Message-----
>From: Jack Connor <[log in to unmask]>
>To: [log in to unmask] <[log in to unmask]>; [log in to unmask] <[log in to unmask]>
>Sent: Tue, Nov 23, 2010 4:50 am
>Subject: RE: [HP3000-L] Disk Array problem continues
>
>
>Greg,
>Is the NIKE bound in RAID1 and are all the discs the same size, or at least the 
>AID1 pairs the same?
>Also, I would probably replace the FWD SCSI terminators on the NIKE if you 
>ren't seeing I/O complete.
>You may want to do a BO ALT from your CSLT and, at the ISL, type ODE, then when 
>DE runs, type RUN MAPPER.
>This will show you what drives are reporting in.  I believe Craig Lalley 
>entioned earlier that the NIKE set up for MPE should report in with C2300WD 
>evice ids.
>Let us know if any of this gets you further down the line.
>Jack
>
>-----Original Message-----
>rom: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of 
>reg Terterian
>ent: Tuesday, November 23, 2010 12:51 AM
>o: [log in to unmask]
>ubject: Re: [HP3000-L] Disk Array problem continues
>Ok, I think I figured out the 1st part of the problem (one of the 4GB disk 
>rives was bad).  I replaced it with 9GB and it seems everything looks ok.  
>owever, when I do an Install from SYSGEN tape, it starts MPE/iX launch facility 
>nd then it displays:
>Install C.39.06 Copyright (c) hewlett packard
>nstall -- MPE/IX disk image builder.
>nitialize genesis - ver bid1: <<pci 2.1601>>
>ate and Time
>nitialize genesis = Ready to configure I/O
>COM}1 12 1 12
>nitialize memory manager completed.
>eginning Install...
>It sits there and does nothing.... I waited for over 30 minutes...
>ape does not flash and no actiivity lights on the disk array...
>Please help!
>hanks a million
>ave
>
>
> To join/leave the list, search archives, change list settings, *
> etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>Call us today about our Windows consulting for monthly support services, plus 
>onfigurations and migrations.
>CONFIDENTIALITY NOTICE: This communication with its contents may contain 
>onfidential information. It is solely for the use of the intended recipient(s). 
>nauthorized interception, review, use or disclosure is prohibited and may 
>iolate applicable laws including the Electronic Communications Privacy Act. If 
>ou are not the intended recipient, please contact the sender and destroy all 
>opies of the communication.
>
>
>* To join/leave the list, search archives, change list settings, *
>* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
>
>
>  
>

* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *