I have had issues like this in the past, although I don't recall if this was the specific error I was getting. What I found was that I was able to restore if I took an account at a time, e.g., "@[log in to unmask]" rather than "@[log in to unmask]@".
Also take into consideration that if you have different disk volume sets, I don't believe Orbit will restore to them by default. You will have to specify implicitly with the ";onvs=volume_set_name" as part of your restore command.
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of Jack Connor
Sent: Wednesday, April 22, 2015 2:44 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Orbit RESTORE
I think it's safe to say the date is OK...
ackuppl.pub.orbit
BACKUP+/iX 6.63A (c)Copyright 1991-15 ORBiT SOFTWARE HOLDING AG 22Apr15
BACKUP+05:52am
+------------------------------------------------+
! BACKUP+/iX : IS VALIDATED !
! Online module : IS VALIDATED !
! Delta module : HAS EXPIRED !
! Wizard module : IS VALIDATED !
+------------------------------------------------+
I'm answering for Billy as he's on site in the 'puter room and may not respond back in a while.
jack
-----Original Message-----
From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of Gsainc
Sent: Wednesday, April 22, 2015 5:38 PM
To: [log in to unmask]
Subject: Re: [HP3000-L] Orbit RESTORE
There was a suggestion earlier - after your first post on this - regarding the system date.
Is it correct and not the default 1972 date that would be the result of a faulty motherboard battery?
Gilles Schipper
Sent via mobile
416-702-7900
> On Apr 22, 2015, at 5:15 PM, Billy Brewer <[log in to unmask]> wrote:
>
> Anyone see the below error when trying to restore from an Orbit Backup tape. Trying to rebuild system after replacing bad disc drive and cannot recover data due to the below. Replaced SCSI cable, terminator, using different FW/SCSI card, even moved the physical drives to other side of Jamaica enclosure to rule out any hardware issues.
> I can also restore the SYS account from a SLT (backed up when they create a SLT) using MPE Restore and it is over 2,000,000 sectors; thus, hardware most likely not the culprit.
> I appreciate any help as not sure what to try next. Thanks error below......
>
>
> RESTORE:74:RESTORE: Unexpected ESCAPE encountered, parms
> =107,-55,11075
>
> Virtual Space Management: A DATA MEMORY PROTECTION trap was detected
> because of an invalid target address alignment.
>
> Billy
> (760) 707-8970
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
Please ask us about Cloud Backup and Disaster Recovery services for your Windows, Linux or Legacy Systems.
CONFIDENTIALITY NOTICE: This communication with its contents may contain confidential information. It is solely for the use of the intended recipient(s). Unauthorized interception, review, use or disclosure is prohibited and may violate applicable laws including the Electronic Communications Privacy Act. If you are not the intended recipient, please contact the sender and destroy all copies of the communication.
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com ______________________________________________________________________
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
