Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
MMSAVE Version 2.5
DUMPAREA found, save main memory to disc
ISL loaded
ISL Revision A.00.43 Apr 12, 2000
***************************************************************************
****** ******
****** Offline Diagnostic Environment ******
****** ******
****** (C) Copyright Hewlett-Packard Co 1993-2000 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** TC Version A.02.22 ******
****** SysLib Version A.00.75 ******
****** Loader Version A.00.61 ******
****** Mapfile Version A.01.27 ******
****** ******
***************************************************************************
Type HELP for command information.
***************************************************************************
****** ******
****** MAPPER2 ******
****** ******
****** Copyright (C) 1998-2000 by Hewlett-Packard Company ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** Version B.00.17 ******
****** ******
***************************************************************************
Type HELP for command information.
STARTING EXECUTION OF MAPPER2
Processor Identification:
Hardware Model: 5D6H, Revision: 0
Software Model: 4H, Revision: 0
Hardware ID: 0, Software ID: 1342988618 (unsigned decimal)
HP-UX Model String: 9000/800/A400-44
MPE/XL Model String: e3000/A400-100-11#N
Processor Board Revisions:
CPU - CPU Chip: 768
PDC - Processor Dependent Code: 41.10
Cache and TLB Sizes:
Instruction Cache: 512 K bytes, Instruction TLB: 160 entries
Data Cache: 1024 K bytes, Data TLB: 160 entries
Co-processors:
Floating Point Co-processor(s) installed
I/O Configuration:
Type HW SW Revisions
Path Component Name ID Model Model Hdwr Firm
(77/124) Continue?
---------- ----------------------------------- ----- ----- ----- ----- -----
0 Astro BC Runway Port CH 582H BH 0 0
0/0 Elroy PCI Bridge DH 782H AH 0 0
0/0/0/0 Ethernet Controller 1011H 0019H 103CH 104FH 41H
0/0/1/0 SCSI Bus Controller 1000H 000BH 0000H 0000H 07H
0/0/1/1 SCSI Bus Controller 1000H 000BH 0000H 0000H 07H
0/0/1/1.15.0
SEAGATE ST39204LC disk drive - - - - HP04
0/0/2/0 Symbios SCSI Controller 1000H 000FH 0000H 0000H 14H
0/0/2/0.5.0
7980S SCSI mag tape unit - - - - A731
0/0/2/1 Symbios SCSI Controller 1000H 000FH 0000H 0000H 14H
0/0/2/1.15.0
SEAGATE ST318404LC disk drive - - - - HP04
0/0/4/0 Serial Controller 103CH 1048H 103CH 1049H 02H
0/0/5/0 Serial Controller 103CH 1048H 103CH 104AH 02H
0/2 Elroy PCI Bridge DH 782H AH 0 0
0/2/0/0 Ethernet Controller 1011H 0019H 103CH 1066H 41H
0/4 Elroy PCI Bridge DH 782H AH 0 0
(96/124) Continue?
0/6 Elroy PCI Bridge DH 782H AH 0 0
8 Memory Controller (256 Mbytes) 1H 9BH 9H 0 0
Slot 01 128M Active
Slot 02 128M Active
Slot 03 - -
Slot 04 - -
Slot 05 - -
Slot 06 - -
Slot 07 - -
Slot 08 - -
160 Processor 0H 5D6H 4H 0 0
Craig Lalley wrote:
> Karsten,
>
> That's a good start. Every one has commented that the drive was seen in Mapper. Can you post the output from MAPPER2?
>
> -Craig
>
>
>
> --- On Thu, 4/30/09, Karsten Brøndum <[log in to unmask]> wrote:
>
>
>> From: Karsten Brøndum <[log in to unmask]>
>> Subject: Re: Mpe: HP7980S Configuration on A400
>> To: [log in to unmask]
>> Date: Thursday, April 30, 2009, 2:50 PM
>> io>
>> io> LP 0/0
>> PATH: 0/0 LDEV:
>> ID: PAT_PCI_BC TYPE: BC
>> PMGR: PCI_ELROY_MGR PMGRPRI: 2
>> LMGR: MAXIOS: 0
>>
>> io> lp 0/0/2
>> PATH: 0/0/2 LDEV:
>> ID: PCI_DEVICE TYPE: BC
>> PMGR: PCI_DEVICE_MGR PMGRPRI: 2
>> LMGR: MAXIOS: 0
>>
>> io> lp 0/0/2/0
>> PATH: 0/0/2/0 LDEV:
>> ID: A5150A TYPE: DA
>> PMGR: PCI_SCSI_DAM PMGRPRI: 6
>> LMGR: MAXIOS: 0
>>
>> io>
>>
>> Thanks,
>> Karsten.
>>
>> Gilles Schipper wrote:
>>
>>> Can you show us, in sysgen, io
>>>
>>> lp 0/0
>>> lp 0/0/2
>>> lp 0/0/2/0
>>>
>>> At 08:51 AM 2009-04-30, SUBSCRIBE HP3000-L Karsten
>>>
>> Brondum wrote:
>>
>>>> Trying to configure an HP7980S on A400, but
>>>>
>> receive
>>
>>>> LLIO Device configuration Error -11
>>>>
>>>> ODE / mapper 2 reports HP7980S on /0/0/2/0.5.0
>>>>
>> which matches path printed
>>
>>>> on back of A400. Did the following configuration:
>>>>
>>>> AP PATH=0/0/2/0.5;ID=PSEUDO
>>>> AD 9;PATH=0/0/2/0.5.0;ID=HP7980S
>>>>
>>>> io> LD 9
>>>> LDEV: 9 DEVNAME: OUTDEV:
>>>>
>> 0 MODE:
>>
>>>> ID: HP7980S RSIZE:
>>>>
>> 128 DEVTYPE: TAPE
>>
>>>> PATH: 0/0/2/0.5.0 MPETYPE:
>>>>
>> 24 MPESUBTYPE: 5
>>
>>>> CLASS: TAPE
>>>>
>>>> :SHOWME
>>>> USER: #S2,MANAGER.SYS,PUB (NOT IN BREAK)
>>>> RELEASE: C.70.00 MPE/iX HP31900 C.39.06 USER
>>>>
>> VERSION: C.70.00
>>
>>>> CURRENT: THU, APR 30, 2009, 2:48 PM
>>>> LOGON: THU, APR 30, 2009, 2:39 PM
>>>>
>>>>
>>>> Any help greatly appreciated
>>>> Karsten.
>>>>
>>>> * To join/leave the list, search archives, change
>>>>
>> list settings, *
>>
>>>> * etc., please visit
>>>>
>> http://raven.utc.edu/archives/hp3000-l.html *
>>
>>>> No virus found in this incoming message.
>>>> Checked by AVG - www.avg.com
>>>> Version: 8.5.285 / Virus Database: 270.12.10/2088
>>>>
>> - Release Date: 04/30/09 06:01:00
>>
>>>
>> -------------------------------------------------------------------------------------------------
>>
>>
>>> Gilles Schipper
>>> GSA Inc.
>>> HP System Administration Specialists
>>> 300 John Street, Box 87651 Thornhill, ON Canada L3T
>>>
>> 7R4
>>
>>> Voice: 905.889.3000 Fax: 905.889.3001
>>> email: [log in to unmask] web: http://www.gsainc.com
>>>
>>>
>> -------------------------------------------------------------------------------------------------
>>
>>
>>>
>>>
>>>
>> * To join/leave the list, search archives, change list
>> settings, *
>> * etc., please visit
>> http://raven.utc.edu/archives/hp3000-l.html *
>>
>
>
>
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
