Ed,

What is the model number?   Have you gone into the data connection settings?

What modes have a asterisk?  (Obviously remote mode is required.)

-Craig

Sent from my iPad

On Nov 30, 2012, at 6:29 AM, Ed King <[log in to unmask]> wrote:

> like this one...
> 
> http://compare.ebay.com/like/190759329793?var=lv&ltyp=AllFixedPriceItemTypes&var=sbar
> 
> 
> a few years ago, my local Ace Hardware stores were giving these away...   I 
> snagged a bunch of 'em
> 
> 
> 
> 
> 
> ----- Original Message ----
> From: "Johnson, Tracy" <[log in to unmask]>
> To: [log in to unmask]
> Sent: Fri, November 30, 2012 9:26:18 AM
> Subject: Re: [HP3000-L] mux-to-console cable pinout
> 
> What "is" a 928 terminal?  I remember 2628, 2626, 2622, 2392, 2382, & 2640 
> terminals, but not a 928.  
> 
> 
> I thought a 928 was the 3000 host?
> 
> 
> Tracy Johnson
> Office (757) 766-4318
> [log in to unmask]
> 
> 
> -----Original Message-----
> From: HP-3000 Systems Discussion [mailto:[log in to unmask]] On Behalf Of Ed 
> King
> Sent: Friday, November 30, 2012 9:13 AM
> To: [log in to unmask]
> Subject: Re: [HP3000-L] mux-to-console cable pinout
> 
> I've tried every which way but loose to make this work. 
> 
> I've...
> 
> a) connected a null modem cable  from mdp to 928 terminal
> b) connected straightthru cable from mdp to 928 terminal
> c) connected a null modem cable  from mdp to linux box running minicom
> d) connected straightthru cable from mdp to linux box running minicom
> 
> No output from the server from any of the above configurations.  Rebooted server 
> each time, also tried various comm settings.  I tried so many combinations, I 
> had to keep a written list to keep track of them all ;)
> 
> Both the physical 928 terminal and the minicom terminal emulator software on 
> linux, work fine when I connect them to other hosts, such as a sparcstation2, so 
> I can't say that there is anything wrong with the "terminals" or the cable
> 
> I've noticed when I boot up the g50, the status lights on the cards in the back 
> of the server may flash amber but after a minute or so, MOST of them end up 
> 
> solid green... except...  the APMUX16 port.   Hmmm.   The APMUX16 status LED 
> flashes amber a few times on boot, then goes off and stays off.  If its not 
> solid green, is that indicative of a problem?  I'd RTFM for the 1703-60022 card 
> if I could find a FM to R ;)
> 
> I think I may try one more thing, an A1703-60003 board with the built-in console 
> port.  If that doesn't work...  the guys at the local scrapyard might mistake 
> this thing for the 2001 space odyssey monolith when I dump it
> 
> 
> 
> 
> 
> ----- Original Message ----
> From: Keven Miller (rtt) <[log in to unmask]>
> To: Ed King <[log in to unmask]>; [log in to unmask]
> Sent: Thu, November 29, 2012 3:17:16 PM
> Subject: Re: [HP3000-L] mux-to-console cable pinout
> 
> I have this setup on my hpux box.
> 
> MDP RS232-C Full Modem 8-port (DB25) PN=5062-3054
> 
> MDP/DDP Cable PN=A1703-63009
> 
> Serial cable PN=40242-60020  (DB25 pins 1,2,3,7)   (MDP port0 to pc serial)
> 
> I believe only pins 2,3,7 (the standard? TX,RX,GND - or is that RX,TX,GND) pin 1 
> doubles as a ground I think.
> 
> Works for me.
> 
> Keven Miller
> 
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
> 
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
> 
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *

* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *