Since last month I've still been trying to configure these disc drives
on my test machine. Someone finally whispered a clue that the some
types of firmware for HP2490AM disc drives MAY not work on HP3000s,
period.
Could someone look at the firmware revisions from MAPPER below and
confirm my suspicions before I rant on the vendor?
:
:DSTAT ALL
LDEV-TYPE STATUS VOLUME (VOLUME SET - GEN)
---------- -------- --------------------------
1-C3010M1 MASTER MEMBER1 (MPEXL_SYSTEM_VOLUME_SET-0)
2-C3010M1 LONER MEMBER2 (MPEXL_SYSTEM_VOLUME_SET-0)
3-C3010M1 LONER MEMBER3 (MPEXL_SYSTEM_VOLUME_SET-0)
4-C2490AM UNKNOWN
5-C2490AM UNKNOWN
8-C2490AM UNKNOWN
:SYSDIAG
*****************************************************************
****** ******
****** ONLINE DIAGNOSTIC SYSTEM ******
****** ******
****** (C) Copyright Hewlett Packard Co. ******
****** 1987, 1989, 1990, 1992, 1994 ******
****** All Rights Reserved ******
****** ******
****** DUI Version A.02.25 ******
****** Diagnostic Monitor Version A.02.31 ******
****** ******
*****************************************************************
Type "HELP" for assistance.
DUI >SYSMAP
*****************************************************************
****** ******
****** SYSTEM MAP ******
****** ******
****** (C) Copyright Hewlett Packard Co. ******
****** 1987 - 1998 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting ******
****** from the use of this program. ******
****** ******
****** Version A.03.45 ******
****** ******
*****************************************************************
Welcome, Today is TUE, FEB 22, 2000 at 1:07 PM
SYSMAP INITIALIZATION IN PROGRESS. PLEASE STAND BY.
ENTER MAP >GENERAL
^
*** THIS COMMAND IS INVALID. TYPE HELP FOR ASSISTANCE.(SYSMAPERR 5000)
ENTER MAP >HELP
commands:
IOMAP (MAP OF THE I/O SYSTEM)
CPUMAP (MAP OF CPUS ON SYSTEM)
MEMMAP (MAP OF MEMORY ON SYSTEM)
MODULEMAP (MAP OF SYSTEM MODULES)
MAPALL (OUTPUT ALL MAPS)
CONFIRM (ON/OFF) (CONFIRM HARDWARE PRESENCE)
TIMEOUT (SET TIME IN SECONDS, FOR CONFIRM MODE)
SHOWSETTINGS (SHOW THE CURRENT SYSMAP SETTINGS)
SUPPRESS (ON/OFF)(SUPPRESS LAN DEVICES OUTPUT)
SUSPEND (SUSPEND THIS PROCESS)
EXIT (EXIT PROGRAM)
ENTER MAP >IOMAP
CONFIRM MODE IN PROGRESS. PLEASE STAND BY.
CONFIRM TRAVERSING SYSTEM TABLES .......................................... CONF
IRM COMPLETE
IOMAP >GENERAL
IOMAP GENERAL HOST MAP
------------------------------------------------------------------------------
CONFIRM MODE IS ON TIMEOUT IS 5 SECOND(S) SUPPRESS DTC DEVICES IS ON
------------------------------------------------------------------------------
Device Adapter(52) --- A1703-60003-SCSI SCSI
Device Adapter(52.0) --- PSEUDO
Device(52.0.0) [ ldev 7 HPC1503B TAPE]
Device Adapter(52.1) --- PSEUDO
Device(52.1.0) [ ldev 8 HPC2490AM DISK]
Device Adapter(52.2) --- PSEUDO
Device(52.2.0) [ ldev 5 HPC2490AM DISK]
Device Adapter(52.3) --- PSEUDO
Device(52.3.0) [ ldev 4 HPC2490AM DISK]
Device Adapter(52.4) --- PSEUDO
Device(52.4.0) [ ldev 3 HPC3010M1 DISK]
Device Adapter(52.5) --- PSEUDO
Device(52.5.0) [ ldev 2 HPC3010M1 DISK]
Device Adapter(52.6) --- PSEUDO
Device(52.6.0) [ ldev 1 HPC3010M1 DISK]
Device Adapter(52.8) --- PSEUDO ***NOT PRESENT***
Device(52.8.0) [ ldev 6 HP2567B LINE PRINTER ***NOT PRESENT***]
Device Adapter(52.9) --- PSEUDO ***NOT PRESENT***
Device(52.9.0) [ ldev 10 HPC1503B TAPE ***NOT PRESENT***]
Local Area Network(56) A1703-60003-CONSOLE/LAN CONSOLE/LAN ->
***LAN DEV'S OUTPUT SUPPRESSED***
------------------------------------------------------------------------------
IOMAP >EXIT
ENTER MAP >EXIT
SYSMAP Exiting...
SYSMAP has terminated
DUI >EXIT
END OF PROGRAM
:
:BYE
CPU=4. Connect=255. TUE, FEB 22, 2000, 1:08 PM.
13:08/#S1/38/LOGOFF ON LDEV #20.
=SHUTDOWN
Shutdown of operating system begins. (Shut 1)
Shutdown of user processes begins. (Shut 2)
Shutdown of jobs & sessions begins. (Shut 3)
Spoolers notified of a shutdown. (Shut 16)
13:08/34/The Spooling system has been shutdown.
Shutdown of system processes begins. (Shut 4)
13:08/45/Predictive Support monitor is shutting down,
13:08/45/[caused by system shutdown command or PS software
13:08/45/upgrade] [8126]
13:13/1Shutdown of system managers begins. (Shut 5)
Shutdown of operating system complete. (Shut 6)
CM> RS
Execution of this command irrecoverably halts all system processing
and I/O activity and restarts the computer system.
Type Y to confirm your intention to restart the system (Y/[N]): Y
SPU hardware was successfully reset. (APMSG 02)
Processor Dependent Code (PDC) revision 1.3
Duplex Console IO Dependent Code (IODC) revision 1
Console path = 56.0.0.0.0.0.0 (dec)
38.0.0.0.0.0.0 (hex)
Primary boot path = 52.6.0.0.0.0.0 (dec)
34.00000006.0.0.0.0.0 (hex)
Alternate boot path = 52.0.0.0.0.0.0 (dec)
34.0.0.0.0.0.0 (hex)
192 MB of memory configured and tested.
Autoboot from primary path enabled.
To override, press any key within 10 seconds.
Boot from primary boot path (Y or N)?> Y
Interact with IPL (Y or N)?> Y
Booting...
Boot IO Dependent Code (IODC) revision 4
HARD Booted.
MMSAVE Version 2.4
DUMPAREA found, save main memory to disc
ISL loaded
ISL Revision A.00.38 OCT 26, 1994
ISL> ODE
***************************************************************************
****** ******
****** Offline Diagnostic Environment ******
****** ******
****** (C) Copyright Hewlett-Packard Co 1993-1998 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** TC Version A.02.13 ******
****** SysLib Version A.00.69 ******
****** Loader Version A.00.47 ******
****** Mapfile Version A.00.99 ******
****** ******
***************************************************************************
Type HELP for command information.
ODE> HELP
ODE> MAPPER
***************************************************************************
****** ******
****** MAPPER ******
****** ******
****** Copyright (C) 1995-1998 by Hewlett-Packard Company ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** Version A.02.34 ******
****** ******
***************************************************************************
Type HELP for command information.
MAPPER> RUN
STARTING EXECUTION OF MAPPER
Processor Identification:
Hardware Model: 280H, Revision: 0
Software Model: 4H, Revision: 0
Hardware ID: 0, Software ID: 1252061321 (unsigned decimal)
Software Cap: 0x10000001
MPE/XL Model String: 959-200
Processor Board Revisions:
CPU - CPU Chip: 3
System Controller: 1
PDC - Processor Dependent Code: 1.3
Cache and TLB Sizes:
Instruction Cache: 64 K bytes, Instruction TLB: 96 entries
Data Cache: 64 K bytes, Data TLB: 96 entries
Co-processors: None installed
I/O Configuration:
Type HW SW Revisions
Path Component Name ID Mod Mod Hdwr Firm
---------- ----------------------------------- ----- ----- ----- ----- -----
52 HP-PB SCSI 4H 14H 39H 0 0
52.0.0 HPC1503(X)/HPC1520B DDS tape - - - - 1009
52.1.0 HPC2490AM disk drive - - - - 3256
52.2.0 HPC2490AM disk drive - - - - 3256
52.3.0 HPC2490AM disk drive - - - - 5193
52.4.0 HPC3010M1 disk drive - - - - 0B04
52.5.0 HPC3010M1 disk drive - - - - 0BW4
52.6.0 HPC3010M1 disk drive - - - - 0B04
56 HP-PB LAN/Console 2H 14H 60H 0 1
62 Processor 0H 280H 4H 0 0
63 Memory (192 M bytes) 1H 14H 9H 0 0
Slot 0A - 32M
Slot 0B - 32M
Slot 1A - 64M
Slot 1B - 64M
RUN COMPLETED.
MAPPER> EXIT
ODE> EXIT
ISL> ODE
***************************************************************************
****** ******
****** Offline Diagnostic Environment ******
****** ******
****** (C) Copyright Hewlett-Packard Co 1993-1998 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** TC Version A.02.13 ******
****** SysLib Version A.00.69 ******
****** Loader Version A.00.47 ******
****** Mapfile Version A.00.99 ******
****** ******
***************************************************************************
Type HELP for command information.
ODE> DISKUTIL
Type HELP for command information.
***************************************************************************
****** ******
****** DISKUTIL ******
****** ******
****** Copyright (C) Hewlett-Packard Co. 1994 thru 1998 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** Version A.00.16 ******
****** ******
***************************************************************************
The bus is being scanned for devices. Please wait.
Sel/
Indx Path Product String Rev Bus Size
---- --------------- ----------------------------------- ------ ------ ------
*0 52.6.0 HPC3010M1 disk drive 0B04 SCSI 1.8 GB
*1 52.5.0 HPC3010M1 disk drive 0BW4 SCSI 1.8 GB
*2 52.1.0 HPC2490AM disk drive 3256 SCSI 1.9 GB
*3 52.2.0 HPC2490AM disk drive 3256 SCSI 1.9 GB
*4 52.3.0 HPC2490AM disk drive 5193 SCSI 1.9 GB
*5 52.4.0 HPC3010M1 disk drive 0B04 SCSI 1.8 GB
Legend:
Sel/Indx - Indx of the disk listed. This is flagged with a '*'
if it is marked for testing.
NOTE:
The size of disk may not match the Information Specified by
the vendor due to difference in calculation methods.
DISKUTIL> HELP
DISKUTIL Help
SUPPORTED COMMANDS ARE
--------------------------------------------------------------------
UTILINFO Quick start on using the utility.
DISPMAP Displays a list of all the disks found
with their present settings.
DISK Changes the list of disk drives to be tested.
DISKINFO Displays the contents of SCSI Inquiry Command for SCSI
and Describe Command for FLEX and CS80 devices.
INQUIRY Implemented as DISKINFO Command.
DESCRIBE Implemented as DISKINFO Command.
ACCESSLOG Reads the log data from the disk.
READBLK Reads the given block from the given disk.
SECTION Sets the test sections to be executed.
RUN Runs all selected sections on the selected disks.
ROMT Performs a read media test on the selected range of
blocks.
--------------------------------------------------------------------
Continue ([y]/n)? Y
ODE Commands Available from DISKUTIL
Basic Commands
--------------
HELP -- Prints detailed information to the screen, when "help <command>"
or "help <var>" is typed
LS -- List modules available on boot medium
RUN -- Run a module (after setting desired environment variables)
Control-Y|Control-C -- Abort an ODE command; pause a module run
RESUME -- Restart a paused module
DISPLOG -- After running a module, display contents of a log
EXIT -- Return to next higher level prompt
Environmental Variables
-----------------------
SHOWSTATE -- Display the value of the following environment variables:
LOOP -- Run a test this many times
ERRPRINT [ON|OFF] -- Print low-level error messages to console
(primarily for manufacturing use)
ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console
Continue ([y]/n)?
ERRPAUSE [ON|OFF] -- Pause module upon error detection
ERRONLY [ON|OFF] -- Print ONLY error messages; disable non-error
and isolation message printing
INFOPRINT [ON|OFF] -- Print informational messages to the console
ISOPRINT [ON|OFF] -- Print fault isolation messages to the console
ISOPAUSE [ON|OFF] -- Pause module when isolation message is generated
LOGSIZE -- Set the size of a message log
DEFAULT -- Reset environment variables to default state
DISKUTIL> DISK
*0 52.6.0 HPC3010M1 disk drive 0B04 SCSI 1.8 GB
Test (Yes/No/Quit)<DEFAULT No>? N
*1 52.5.0 HPC3010M1 disk drive 0BW4 SCSI 1.8 GB
Test (Yes/No/Quit)<DEFAULT No>? N
*2 52.1.0 HPC2490AM disk drive 3256 SCSI 1.9 GB
Test (Yes/No/Quit)<DEFAULT No>? Y
*3 52.2.0 HPC2490AM disk drive 3256 SCSI 1.9 GB
Test (Yes/No/Quit)<DEFAULT No>? Y
*4 52.3.0 HPC2490AM disk drive 5193 SCSI 1.9 GB
Test (Yes/No/Quit)<DEFAULT No>? Y
*5 52.4.0 HPC3010M1 disk drive 0B04 SCSI 1.8 GB
Test (Yes/No/Quit)<DEFAULT No>? N
DISKUTIL> SECTION
-------------------------------------------------
Section Description
-------------------------------------------------
*1 Selftest
*2 Butterfly Seek Test
*3 Read Error Rate Test
-------------------------------------------------
A '*' besides a Section Number indicates that it
is selected for testing.
DISKUTIL> RUN
STARTING EXECUTION OF DISKUTIL
Testing HPC2490AM disk drive Index 2
------------------------------------------------------------
SECTION 001
SelfTest being done.
SelfTest done successfully.
SECTION 002
Butterfly Seek Test being done.
10% Complete
20% Complete
30% Complete
40% Complete
50% Complete
60% Complete
70% Complete
80% Complete
90% Complete
100% Complete
Butterfly Seek Test done successfully.
SECTION 003
Read Media Test being done.
......... 10% Complete
......... 20% Complete
......... 30% Complete
......... 40% Complete
......... 50% Complete
......... 60% Complete
......... 70% Complete
......... 80% Complete
......... 90% Complete
.........100% Complete
Read Media Test done successfully.
Testing HPC2490AM disk drive Index 3
------------------------------------------------------------
SECTION 001
SelfTest being done.
SelfTest done successfully.
SECTION 002
Butterfly Seek Test being done.
10% Complete
20% Complete
30% Complete
40% Complete
50% Complete
60% Complete
70% Complete
80% Complete
90% Complete
100% Complete
Butterfly Seek Test done successfully.
SECTION 003
Read Media Test being done.
......... 10% Complete
......... 20% Complete
......... 30% Complete
......... 40% Complete
......... 50% Complete
......... 60% Complete
......... 70% Complete
......... 80% Complete
......... 90% Complete
.........100% Complete
Read Media Test done successfully.
Testing HPC2490AM disk drive Index 4
------------------------------------------------------------
SECTION 001
SelfTest being done.
SelfTest done successfully.
SECTION 002
Butterfly Seek Test being done.
10% Complete
20% Complete
30% Complete
40% Complete
50% Complete
60% Complete
70% Complete
80% Complete
90% Complete
100% Complete
Butterfly Seek Test done successfully.
SECTION 003
Read Media Test being done.
......... 10% Complete
......... 20% Complete
......... 30% Complete
......... 40% Complete
......... 50% Complete
......... 60% Complete
......... 70% Complete
......... 80% Complete
......... 90% Complete
.........100% Complete
Read Media Test done successfully.
RUN COMPLETED.
DISKUTIL>
DISKUTIL> HELP
DISKUTIL Help
SUPPORTED COMMANDS ARE
--------------------------------------------------------------------
UTILINFO Quick start on using the utility.
DISPMAP Displays a list of all the disks found
with their present settings.
DISK Changes the list of disk drives to be tested.
DISKINFO Displays the contents of SCSI Inquiry Command for SCSI
and Describe Command for FLEX and CS80 devices.
INQUIRY Implemented as DISKINFO Command.
DESCRIBE Implemented as DISKINFO Command.
ACCESSLOG Reads the log data from the disk.
READBLK Reads the given block from the given disk.
SECTION Sets the test sections to be executed.
RUN Runs all selected sections on the selected disks.
ROMT Performs a read media test on the selected range of
blocks.
--------------------------------------------------------------------
Continue ([y]/n)? N
DISKUTIL> EXIT
ODE> EXIT
ISL> START NORECOVERY LOGON=CONSOLE,MANAGER.SYS
MPE/iX launch facility
Initialize_genesis - Version : <<870204.1552>>
TUE, FEB 22, 2000, 2:14:33 PM (y/n)? Y
[CDM]11 1 4 10
Initialize genesis completed.
Create Console Messages kso completed.
Initialize memory manager completed.
Initialize resident kernel completed.
Initialize volume management and mount the System Disk
Initialize volume management completed.
Opening the native system library completed.
Initialize loader completed.
I/O boot path managers frozen in memory completed.
Vsm make no longer resident completed.
Initialize process management completed.
Initialize debug subsystem completed.
Initialize file system completed.
Initialize temporary UID/GID Databases completed.
Initialize non-resident services completed.
Begin binding compatibility mode SL
Compatibility mode SL binding complete
Create port process has been completed.
The following is a list of the boot options -
last boot command: START last configuration group: CONFIG
current boot command: START current configuration group: CONFIG
Last configuration group actually used by START: CONFIG
logon = CONSOLE,MANAGER.SYS
NORECOVERY MULTI-USER
MULTI-DISK SYSSTART
Begin launching additional processors:
No additional processors found: 1 total processor.
Entering - System I/O configuration.
The path 52 has already been configured.
The path 52.6.0 has already been configured.
The path 52.8.0 was configured but is not available.
The path 52.9.0 was configured but is not available.
The path 56 has already been configured.
The path 56.0 has already been configured.
Leaving - System I/O configuration.
SYSTEM I/O AT BOOT TIME
ldev: 1 HPC3010M1 configured available 52.6.0
ldev: 2 HPC3010M1 configured available 52.5.0
ldev: 3 HPC3010M1 configured available 52.4.0
ldev: 4 HPC2490AM configured available 52.3.0
ldev: 5 HPC2490AM configured available 52.2.0
ldev: 6 HP2567B configured not-available 52.8.0
ldev: 7 HPC1503B configured available 52.0.0
ldev: 8 HPC2490AM configured available 52.1.0
ldev: 10 HPC1503B configured not-available 52.9.0
ldev: 20 A1703-60003-CONS configured available 56.0
ldev: 21 A1703-60003-CONS configured available 56.1
MEMORY AVAILABLE FOR USE (bytes): 201326592
Entering - Mount all volumes
Mounting MASTER on LDEV 1
Mounting MEMBER on LDEV 8
Mounting MEMBER on LDEV 5
Mounting MEMBER on LDEV 4
Mounting MEMBER on LDEV 3
Mounting MEMBER on LDEV 2
USERLOG RECOVERY COMPLETED for MPEXL_SYSTEM_VOLUME_SET
NO PARALLEL PROCESSES FOR MOUNT_ALL_VOLUMES
-- Time spent in MOUNT_ALL_VOLUMES -> 2
Leaving - Mount all volumes
The current boot command has been saved on the system master.
NMLG FILE NUMBER 4 ON.
14:15/22/UNABLE TO OPEN SOCKET LOGGING; NM ERROR = 16. (SOCKETS 702)
14:15/22/DCC STARTUP - ENTER - version C0300001 compiled 970612
14:15/22/DCC ERROR 122-1, Configuration file open error 001000B4. (DCCERR=3)
14:15/22/DCC WARNING 122-6, Configuration file close error 003600B4. (DCCWARN=2
1)
14:15/22/DCC WARNING 123-1, (Startup) can not open NMCONFIG, status FF09008F.
(DCCWARN=101)
14:15/29/DCC ERROR 3-1, Configuration file open error 001000B4. (DCCERR=3)
14:15/22/DCC STARTUP - ERROR
[NETWORK_DUMP_SURR] Version A.00.60.001
System State: Initializing Mode.
Reply Information Table has been initialized!
System State: Multiuser Mode.
14:15/1/Spooling of initially spooled devices is complete.
14:15/1/Set-up of Spooling Subsystem is complete.
SYSTEM LOG FILE #5 IS ON
Initializing Job & Session
Initiate Operator Log On
Successfully launched Optical Media Manager process.
JOB Scheduling Initialized
SESSION Scheduling Initialized
14:15/40/No Optical device, Optical Media Manager process terminated
Successfully launched diagnostic monitor process.
Successfully launched System UPS Monitor process.
14:15/#S1/38/LOGON FOR: "CONSOLE,MANAGER.SYS,PUB" ON LDEV #20.
HP3000 Release: C.60.00 User Version: C.60.00 TUE, FEB 22, 2000, 2:15 PM
MPE/iX HP31900 C.16.01 Copyright Hewlett-Packard 1987. All rights reserved.
:DSTAT ALL
LDEV-TYPE STATUS VOLUME (VOLUME SET - GEN)
---------- -------- --------------------------
1-C3010M1 MASTER MEMBER1 (MPEXL_SYSTEM_VOLUME_SET-0)
2-C3010M1 LONER MEMBER2 (MPEXL_SYSTEM_VOLUME_SET-0)
3-C3010M1 LONER MEMBER3 (MPEXL_SYSTEM_VOLUME_SET-0)
4-C2490AM UNKNOWN
5-C2490AM UNKNOWN
8-C2490AM UNKNOWN
:VOLUTIL
Volume Utility A.02.00, (C) Hewlett-Packard Co., 1987. All Rights Reserved.
volutil: NEWVOL MPEXL_SYSTEM_VOLUME_SET:MEMBER4 4 100 100
*Verify: Initialize new member volume MPEXL_SYSTEM_VOLUME_SET:MEMBER4 on ldev 4
[Y/N] ?Y
DISMOUNT REQUEST FOR LDEV 4 GRANTED (AVR 19)
BEGIN VOLUME MOUNTING ON LDEV 4 (AVR 9)
UNKNOWN VOLUME MOUNTED ON LDEV 4 (AVR 15)
*Error: WARNING ** Message set 113, Error number 32 was not found in the system
catalog.
volutil: FORMATVOL 4
*Verify: Format volume on ldev 4 [Y/N] ?Y
DISMOUNT REQUEST FOR LDEV 4 GRANTED (AVR 19)
BEGIN VOLUME MOUNTING ON LDEV 4 (AVR 9)
UNKNOWN VOLUME MOUNTED ON LDEV 4 (AVR 15)
*Error: WARNING ** Message set 113, Error number 32 was not found in the system
catalog.
volutil: SCRATCHVOL 4
^
*Error: Volume mounted in invalid state for desired operation. (volutil 122)
volutil: EXIT
Tracy M. Johnson
TRW Automotive Electronics
Sensors & Components
|
