Restore the config group from a backup tape made before the problem,
shutdown, then start norecovery. Whether the device is real or pseudo
the path must be available.

                  Bob J. -- Ideal Computer Services
                  http://www.icsgroup.com



Warren Cartwright wrote:
>
> Thank you all for your prompt replies.  However, it still doesn't work.
> Here are the error messages which appear during boot:
>
> ...
> The path 4.1.7 was configured but is not available
> LLIO error - subsys: 129, proc num: 58, error_num: -15
> for path 4.1.8
> ERROR - LLIO device configuration error: -11
>                 status - subsys: #150 info: #-11
> ...
> STREAMS 10
> STREAMS device cannot be a terminal (CIERR 3067)
> ...
> STREAM NETJOB.PUB.SYS
> Stream facility not enables. See operator. (CIERR 82)
> ...
>
> The last message does me no good, I AM the operator.
> I have not been able to find any info on any of this on the HP LaserROM for
> MPE 5.0.  We are running MPE 5.0, and (for financial reasons, surprise,
> suprise) we have no HP support either for hardware or software.  (Not MY
> decision)
> Thanks again, y'all are great.
> W.
> [log in to unmask]
>
> Gary Nolan wrote:
>
> > Hi,
> > I just checked my system config for ldev 10 and here it is:
> >  LDEV:    10  DEVNAME:        OUTDEV:       LP   MODE:  JA
> >    ID: HPC1503B               RSIZE:       128   DEVTYPE: TAPE
> >  PATH: 52.9.0                 MPETYPE:      24   MPESUBTYPE:  7
> > CLASS: JOBTAPE
> >
> > We are on a 947. Hope this helps.
> > Gary Nolan
> > Sydney Steel Corporation
> >
> > -----Original Message-----
> > From:   Warren Cartwright [SMTP:[log in to unmask]]
> > Sent:   May 12, 1998 7:36 PM
> > To:     [log in to unmask]
> > Subject:        HELP  ldev 10 spooler
> >
> > I inadvertantly deleted ldev 10 on our 3000-920.  I can't figure out how
> > to get it back successfully!
> >
> > I have added an LP device on ldev 6 and the ldev 10, sysgen> io>ld looks
> > like this:
> >
> >      io> ld 6
> >  LDEV:     6  DEVNAME:                    OUTDEV:        0
> > MODE:          OS
> >    ID: HP2566A                            RSIZE:        66   DEVTYPE: LP
> >
> >  PATH: 4.1.7                              MPETYPE:      32
> > MPESUBTYPE:  9
> > CLASS: LP
> >
> >      io> ld 10
> >  LDEV:    10  DEVNAME:                    OUTDEV:       LP   MODE:  JA
> >    ID: HPC1501A                           RSIZE:       128   DEVTYPE:
> > TAPE
> >  PATH: 4.1.8                              MPETYPE:      24
> > MPESUBTYPE:  6
> > CLASS: JOBTAPE
> >
> >      io>
> >
> > When I boot the machine, I get errors wrt ldev 6 and 10.  When I type
> > streams 10, the computer tells me that the spool device can't be a
> > terminal and aborts.
> >
> > How do I get my streams back?!?
> >
> > W.
> > [log in to unmask]