To All,
I would just add to Craig's response, if you have a current back-up tape
with ALL the directories specified for all the volume sets, after replaceing
and re-intializing the corrupted volume set, you can :restore
*t;;directory;show which will restore all the directories on the store tape.
Additionally, this will allow
the restore of command.pub.sys (if not on the wiped out disc volume) to set
UDC's without the BULDJOB2. If youn just have to restore a volume set, you
can then ;KEEP a lot of your files without re-writing them..
Chuck Ciesinski
----- Original Message -----
From: "Craig Lalley" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Saturday, June 04, 2005 12:22 AM
Subject: Re: [HP3000-L] Reload
> Jose,
>
> It sounds like you got the picture... let me see if I can put them in step
>
> First make sure you have
> 1) a full backup
> 2) a CSLT
> 3) A tape with the BULDJOB1 and BULDJOB2 (files created by BULDACCT), I
> also like to put NMCONFIG.PUB.SYS, @.NET.SYS, QUAD.PUB.SYS (or any other
> editor you use) and a few others, but I am doing this from memory
>
> You can create 2 and 3 even if the drive is bad, as long as the bad drive
> is not LDEV1
>
> OK, so replace the drive... I am assuming everything is in one volume set,
> hence the requirement for a reload.
>
> So replace the drive.
>
> 1) put the CSLT tape in and boot from the alternate path > BO PRI
> 2) and the ISL prompt enter INSTALL answer Yes to begin the process
> the system will reboot when it is done
> 3) put the tape with @.NET.SYS in and restore it.
> 4) VOLUTIL
> NEWVOL MPEXL_SYSTEM_VOLUME_SET:MEMBER2 2 100 100
>
> Do this for each drive changing the member name and ldev
> 5) RESTORE the special tape with @.NET.SYS and the BULDJOB1
> 6) STARTSPOOL LP
> 7) STREAMS 10
> 8) STREAM BULDJOB1 to put the accounting structure back
> 9) This is important, create a job to do the RESTORE
> @[log in to unmask]@;KEEP;SHOW;OLDDATE:PARTDB
>
> The reason why you want to do it in a job, is so you don't tie up the
> console... also when it is done, the show will be VERY long at 9600 bps.
>
> 10) reboot the box START NORECOVERY
> 11) STREAM BULDJOB2 to get the UDC'S back
>
> You should be done.
>
> I did this off the top of my head so, I may be missing something, but I am
> sure others on the list will find it.
>
> Regards,
>
> -Craig
>
>
> "Jose B. Aguilar" <[log in to unmask]> wrote:
> Help !!!
>
> I need to replace a disk and I don't remeber what the steps are to do the
> reload. Any suggestions? I mean within reason.
>
> I know about the full system backups using the ";directory" parameter.
> I remember that I should have 2 backups and a SLT tape created.
> And after the drives is replaced, I need to do a VOLUTIL to scratch the
> drives. Then after the NEWVOLs are created, I do a restore. Is that all I
> have to do?
> I know about the BULDACCT at the start of this process and know that the
> UDCs wont be available untill after the restore from the back up tapes.
> Then I do another boot with 'START NORECOVERY'.
>
> I hope thats all I have to do , cause thats about all I remember.
>
> Thanks, in advance for any comments or suggestions.
>
> BTW, we're on a 968 running MPEiX 6.0........
>
> Jose B. Aguilar
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
>
> ---------------------------------
> Discover Yahoo!
> Get on-the-go sports scores, stock quotes, news & more. Check it out!
>
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
>
* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
|
