now we're on the right track I think...  
nmmgr
f1 = Open Config,
F1 = DTS,
F1 = Go To DTC,
F1 = List DTCs; only one on list = DTC01. F8 = Prior Screen.
F2=16ix_nope;F3=16MX/RX_nope;F4=DTC16_nope;F5=DTC48_there it is!
F1 = ReadDTC,
NMMGR/3000 (B.06.00) #175 DTC48 Configuration
Data: Y 
Fill in the required information; then press the Save Data key.

Command:


To see another DTC, enter the name then press Read DTC:
 
  DTC name: [DTC01   ]   DTC LAN station address: [08-00-09-18-E9-8F]
(in hex)

  DTC node name: [DTC01.GATE.COM                                    ] 
                             (node.domain.organization)
  DTC IP Address: [                 ] (optional)   Enable logging class:
(Y/N)
                                                     1  Y   2 [Y]  3 [Y]
  Enter card types as installed in DTC:              4 [N]  5 [N]  6 [N]

    Card #  Type

      0     [M]  (D = Direct connect            
      1     [ ]   M = Modem)                    
      2     [ ]                                
      3     [ ]                                                        
      4     [ ]
      5     [M]

 
To configure a card, enter a card number then press Config Card. [0]
       
File:  NMCONFIG.PUB.SYS 

F4=Config Card.  Nothing on card 0; card 5 shows port 0 ldev 900 profile
PRNETPR.

hmmm, maybe not quite the right track.  
all but ldev 23 in the npconfig.pub.sys list below work per these specs,
via IP addresses.  ldev 23 exists, is spooled, DISTSERV exists only in
ioconfig.  Need to equate DISTSERV to ldev 23 to complete the loop,
can't figure out where to do that.

thought I had this down but it's been a while. 

> -----Original Message-----
> From: [log in to unmask] [mailto:[log in to unmask]] 
> Sent: Tuesday, October 30, 2007 11:39 AM
> To: Tracy Pierce
> Subject: Re: [HP3000-L] network printing
> 
> One last thing, you create a dummy DTC in mnngr and add the 
> devclasses there
> 
> From: Tracy Pierce <[log in to unmask]>
> Date: 2007/10/30 Tue PM 01:03:58 CDT
> To: [log in to unmask]
> Subject: [HP3000-L] network printing
> 
> can't remember how to do this!  ioconfig listclass leads me to think I
> had devclass DISTSERV pointing to ldev 900 (once used by MS 
> NetPrint); I
> want to make that devclass work as ldev 23.  but DISTSERV seems to be
> lost...
> IOCONFIG A.00.00 (catalog A.00.00) (c) 1994 Hewlett-Packard Co. All
> Rights Reser
> ved. TUE, OCT 30, 2007, 10:48 AM
> 
>         **note** Retrieving NMMGR configuration data...
> ioconfig:listclass
> CLASSNAME   MODE     LDEV(S) 
> ---------   ----     -------
> DLT         ncio     12
> TAPE        ncio     8, 7, 9
> DAT9        ncio     9
> DISC        random   5, 3, 2, 1
> SPOOL       random   5, 3, 2, 1
> JOBTAPE     ncio     10
> CONSOLE     cio      20
> TERM        cio      21
> LP          out      11
> HP5SIMX     out      13, 900
> <some snippage>
> SRTRAIN     out      22, 900
> BUSPARTS    out      24, 900
> ....
> DISTSERV    out      900       
> HR4050T     out      900
> SRSCHLJ5    out      900
> ioconfig:MCLASS DISTSERV ALDEV 23
> Class DISTSERV is not configured in the system currently. 
> (IOCONFIG 25)
> ioconfig:exit
> (HOBBES/SYS/PUB)/SHOWDEV DISTSERV
> Logical device class "!" cannot be found on the system. (CIERR 1583)
> 
> How please do I create the devclass and point it at ldev 23?  The
> npconfig line's already in place:
> 
> 23      (network_address=10.10.3.142)  # DISTSERV SF District Services
> was PQ-DISTSERV-HP4050TN
> 
>  
> Tracy Pierce
> chair-keyboard ram failure?
> 
> * To join/leave the list, search archives, change list settings, *
> * etc., please visit http://raven.utc.edu/archives/hp3000-l.html *
> 
> 
> joseph dolliver
> e3k solutions , inc
> 41630 marie court
> leonardtown, md 20650
> 

* To join/leave the list, search archives, change list settings, *
* etc., please visit http://raven.utc.edu/archives/hp3000-l.html *